1、Designation: F1544 11An American National StandardStandard Specification forDetermining the Rating Velocities of a Compound ArcheryBow1This standard is issued under the fixed designation F1544; the number immediately following the designation indicates the year oforiginal adoption or, in the case of
2、 revision, the year of last revision. A number in parentheses indicates the year of last reapproval. Asuperscript epsilon () indicates an editorial change since the last revision or reapproval.1. Scope1.1 This specification covers the testing technique to deter-mine the rating velocities of a compou
3、nd bow.1.2 This specification will provide only a certification ofperformance, that is, the velocities at which a given bow willlaunch arrows of specified weights under standard conditions.1.3 This specification is not intended to provide any engi-neering or structural evaluation of the bow that wou
4、ld deter-mine its fitness for the use intended, safe function, or any otherattribute except as stated.1.4 The values stated in inch-pound units are to be regardedas standard. The values given in parentheses are mathematicalconversions to SI units that are provided for information onlyand are not con
5、sidered standard.1.5 The following safety hazards caveat pertains only to thetest methods portion, Section 4, of this specification: Thisstandard does not purport to address all of the safety concerns,if any, associated with its use. It is the responsibility of the userof this standard to establish
6、appropriate safety and healthpractices and determine the applicability of regulatory limita-tions prior to use.2. Terminology2.1 Definitions of Terms Specific to This Standard:2.1.1 archery trade association (ATA) draw length, nthedistance at the archers full draw from the string at the nockingpoint
7、 to a vertical line through the pivot point of the bow grip134 in. (+14 in., 0 in.) (44 + 6.4 0 mm).2.1.2 draw length pressure point (DLPP) draw length,nthe distance at the archers full draw from the string at thenocking point to a vertical line through the distal or pivot pointof the bow grip.2.1.3
8、 force-draw curvethe graph curve generated by re-cording the draw force readings of an archery bow at 1.0-in.(25.4-mm) intervals or less, from brace height through setweight and to the center of the valley (if present), in order toreveal the energy storage characteristics of the bow.2.1.4 rating vel
9、ocities, nthe initial velocity of an arrowweighing 5 grains per pound (0.073 g/N) of the bows PeakDraw Force (60.5 grains (60.03 g) on total arrow weight)(0.03 g) from a bow set at no more than 70 612 lb (311.4 N)Peak Draw Force and 30 in. (762 mm) ATA actual draw length.Example: a 70-lb Peak Draw F
10、orce bow requires the use of a350 grain (22.7 g) arrow (60.5 grains (60.03 g) on total arrowweight) (0.03 g 6 0.4 N). A minimum of (5) shots for each testmust be performed. Test shot velocities will then be averagedto determine the ATA Compound Bow Rating Velocity.2.1.5 shooting machinea device, equ
11、ipped with a me-chanical release, that secures a bow and releases an arrow toobtain highly repeatable shooting results for various testingpurposes.2.1.6 stored energythe energy required to draw a bowfrom brace height to full draw, usually expressed in foot-pounds (joules).3. Significance and Use3.1
12、This specification will be used to determine a velocityunder standard test conditions for rating an archery bow.4. Test Methods4.1 Force Draw Data:4.1.1 For bows with adjustable draw force, adjust peak ormaximum draw force to no more than 70 6 0.5 lb (311.4 62.22 N). The center of the valley of the
13、force-draw curve(lowest force) attained after having passed through the peak ormaximum draw force shall be located at 2814-in. (717.6 mm)DLPP, +14 0 in. (6 mm).4.1.2 Measure and record the draw force at 1.0-in. (25.4-mm) (or less) increments from brace height to at least 2814-in.(717-mm) DLPP (30-in
14、 (762-mm) ATA) draw length.4.1.3 From the force-draw curve (obtained in 4.1.2), deter-mine the peak or maximum draw force that occurs between thebrace position of the bow and the full draw length of 2814-in.(717-mm) DLPP (30-in. (762-mm) ATA).1This specification is under the jurisdiction of ASTM Co
15、mmittee F08 on SportsEquipment and Facilities and is the direct responsibility of Subcommittee F08.16 onArchery Products.Current edition approved Nov. 1, 2011. Published November 2011. Originallyapproved in 1994. Last previous edition approved in 2009 as F1544 09. DOI:10.1520/F1544-11.1Copyright AST
16、M International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959, United States.4.2 Test Arrows:4.2.1 Select the test arrows of a shaft material, size, andsufficient spine to match the test bows Peak Draw Force anddraw length. The test arrows must also meet the 5 grain perpound
17、0.073 g/N) of the test bows Peak Draw Force weightrequirement (60.5 grain (0.03 g). (Refer to example shown in2.1.4).4.2.2 The arrows need not be fletched.4.3 Set up the test bow in the shooting machine.4.3.1 Mount the bow in a shooting machine with a mechani-cal release. Set the draw length at 281
18、4-in. (717-mm) DLPP (30+18 , 0 in. (762 + 3.2, 0 mm) ATA).4.3.2 Set the initial chronograph gate at a distance of 36 in.(914 mm) from the pivot point of the bows handle.4.4 Shooting Test:4.4.1 Chronograph a minimum of five shots for each testarrow using the standard test arrow to obtain a satisfacto
19、ryarrow velocity average. The average velocity is determinedfrom a minimum of five shots of the test arrow in which no testvelocity more than 2 ft/s (0.61 m/s) from any other testvelocity.4.4.2 Use an appropriate multiple gate chronograph.5. Keywords5.1 draw length; force draw curve; rating velocity
20、 shootingmachine; stored energyASTM International takes no position respecting the validity of any patent rights asserted in connection with any item mentionedin this standard. Users of this standard are expressly advised that determination of the validity of any such patent rights, and the riskof
21、infringement of such rights, are entirely their own responsibility.This standard is subject to revision at any time by the responsible technical committee and must be reviewed every five years andif not revised, either reapproved or withdrawn. Your comments are invited either for revision of this st
22、andard or for additional standardsand should be addressed to ASTM International Headquarters. Your comments will receive careful consideration at a meeting of theresponsible technical committee, which you may attend. If you feel that your comments have not received a fair hearing you shouldmake your
23、 views known to the ASTM Committee on Standards, at the address shown below.This standard is copyrighted by ASTM International, 100 Barr Harbor Drive, PO Box C700, West Conshohocken, PA 19428-2959,United States. Individual reprints (single or multiple copies) of this standard may be obtained by contacting ASTM at the aboveaddress or at 610-832-9585 (phone), 610-832-9555 (fax), or serviceastm.org (e-mail); or through the ASTM website(www.astm.org). Permission rights to photocopy the standard may also be secured from the ASTM website (www.astm.org/COPYRIGHT/).F1544 112
