1、BRITISH STANDARD BS 5505-3: 1977 Specification for Bidets Part 3: Vitreous china bidets over rim supply only Quality, workmanship and functional dimensions other than connecting dimensions UDC 696.141.5:645.683.6BS5505-3:1977 This British Standard, having been prepared under the directionof the Sani
2、tary Appliances Standards Committee,was published underthe authorityof the Executive Board on 30 September 1977 BSI 07-1999 The following BSI references relate to the work on this standard: Committee reference SAB/1 Draft for comment 76/11247 DC ISBN 0 580 09865 6 Cooperating organizations The Sanit
3、ary Appliances Standards Committee, under whose direction this British Standard was prepared, consists of representatives from the following Government departments and scientific and industrial organizations: Bath Manufacturers Co-ordinating Committee Chartered Institution of Building Services Counc
4、il of British Ceramic Sanitaryware Manufacturers* Department of the Environment Department of the Environment, Building Research Establishment* Department of the Environment, Housing and Construction* Department of the Environment, Property Services Agency* Environmental Health Officers Association*
5、 Greater London Council Institute of Plumbing* Institution of Municipal Engineers* Institution of Public Health Engineers* Metal Sink Manufacturers Association* Ministry of Defence National Brassfoundry Association* National Federation of Builders and Plumbers Merchants* National Water Council* Roya
6、l Institute of British Architects Royal Institute of Public Health and Hygiene Royal Society of Health Water Companies Association The organizations marked with an asterisk in the above list, together with the following, were directly represented on the committee entrusted with the preparation of th
7、is British Standard: British Bath Manufacturers Association British Ceramic Research Association British Ironfounders Association British Plastics Federation British Woodwork Manufacturers Association Consumer Standards Advisory Committee of BSI Good Housekeeping Institute Institution of Water Engin
8、eers and Scientists Modular Society Ltd. National Association of Plumbing, Heating and Mechanical Services Contractors Plastics Bath Manufacturers Association South London Consortium Individual manufacturer Amendments issued since publication Amd. No. Date of issue CommentsBS5505-3:1977 BSI 07-1999
9、i Contents Page Cooperating organizations Inside front cover Foreword ii Section 1. General 1 Scope 1 2 References 1 3 Marking 1 4 Inspection 1 5 Rejection 1 Section 2. Materials, quality and workmanship 6 Materials 1 7 Quality 1 8 Floor fixing holes 1 9 Overflow 1 10 Tap platform 1 11 Soap sinking(
10、s) 1 Section 3. Functional dimensions (other than connecting dimensions) 12 General 1 Figure 1 Plan of bidet (separate pillar taps or centre set) 2 Table 1 Functional dimensions for pedestal and wall hung bidets 1 Table 2 Functional dimensions for pedestal bidets only 1 Table 3 Functional dimensions
11、 for pedestal and wall hung bidets forusewithpillar taps or centre set with pop-up waste 2 Publications referred to Inside back coverBS5505-3:1977 ii BSI 07-1999 Foreword This Part of this British Standard has been prepared under the direction of the Sanitary Appliances Standards Committe in order t
12、o supplement the following standards. BS 5505, Bidets Part 1 EN 35: Pedestal bidets over rim supply only Connecting dimensions. BS 5505, Bidets Part 2 EN 36: Wall hung bidets over rim supply only Connecting dimensions. A British Standard does not purport to include all the necessary provisions of a
13、contract. Users of British Standards are responsible for their correct application. Compliance with a British Standard does not of itself confer immunity from legal obligations. Summary of pages This document comprises a front cover, an inside front cover, pages i and ii, pages1 and 2, an inside bac
14、k cover and a back cover. This standard has been updated (see copyright date) and may have had amendments incorporated. This will be indicated in the amendment table on the inside front cover.BS5505-3:1977 BSI 07-1999 1 Section 1. General 1 Scope This Part of this British Standard specifies requirem
15、ents for materials, quality, workmanship and functional dimensions (other than connecting dimensions) for pedestal and wall hung bidets over rim supply, for use with pillar taps or centre set with pop-up waste. 2 References The titles of the publications referred to in this standard are listed on th
16、e inside back cover. 3 Marking Bidets manufactured to the requirements of this standard shall be permanently marked with the following information. a) The manufacturers name or identification mark. b) The number of this British Standard, i.e.BS5505-3. c) Either EN 35 or EN 36 as appropriate. 4 Inspe
17、ction The purchaser or his representative shall, if required, be granted facilities for the purpose of carrying out inspection prior to delivery. 5 Rejection The purchaser shall have the option of rejecting any bidet purporting to meet the requirements of BS5505 if it fails to meet any of the requir
18、ements laid down therein. Minor imperfections which do not affect the appearance or efficiency of the article shall not constitute valid reasons for rejection. Section 2. Materials, quality and workmanship 6 Materials Bidets shall be manufactured from vitreous china. 7 Quality Vitreous china bidets
19、shall comply with the requirements of BS 3402. 8 Floor fixing holes A minimum of two floor fixing holes shall be provided. 9 Overflow An overflow, if provided, shall have an aperture area of not less than 600 mm 2 . 10 Tap platform The level of the top of the platform that accommodates the taps shal
20、l not be below the spillover level of the bidet irrespective of the overflow slot. 11 Soap sinking(s) Any soap sinking shall adequately drain into the bowl and not into the overflow. Section 3. Functional dimensions (other than connecting dimensions) 12 General Bidets shall comply with the functiona
21、l dimensions given in Table 1, Table 2 and Table 3 (see Figure 1), and the connecting dimensions given in BS 5505-1 EN 35 or BS 5505-2 EN 36 as appropriate. Table 1 Functional dimensions for pedestal and wall hung bidets (see Figure 1) Table 2 Functional dimensions for pedestal bidets only (see Figu
22、re 1) Description Dimensions mm Overall length of bidet 550 min. Overall width of bidet 400 max. Description Dimensions mm Length of base 250 min. Width of base 180 min.BS5505-3:1977 2 BSI 07-1999 Table 3 Functional dimensions for pedestal and wall hung bidets for use with pillar taps or centre set
23、with pop-up waste (see Figure 1) Reference letter Description Dimensions mm A Distance from centreline of tap hole to edge of bowl 60 max. B Centreline of tap holes for pillar taps or centre set 100 2 C Diameter of chain stay hole for pillar taps and for 100 2 mm centre set with pop-up waste d 1 Dia
24、meter of tap holes t Horizontal distance between centreline of tap holes and centreline of waste hole 170 max. 10 0 + 2 302 + 0 NOTEDrawing is diagrammatic only. Figure 1 Plan of bidet (separate pillar taps or centre set)BS5505-3:1977 BSI 07-1999 Publications referred to BS 3402, Quality of vitreous
25、 china sanitary appliances. BS 5505, Specification for bidets. BS 5505-1 EN 35, Pedestal bidets over rim supply only Connecting dimensions. BS 5505-2 EN 36, Wall hung bidets over rim supply only Connecting dimensions. BS 5505-3: 1977 BSI 389 Chiswick High Road London W4 4AL BSIBritishStandardsInstit
26、ution BSI is the independent national body responsible for preparing BritishStandards. It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter. Revisions BritishStandards are updated by amendment or revision. Users of BritishStandards should
27、 make sure that they possess the latest amendments or editions. It is the constant aim of BSI to improve the quality of our products and services. We would be grateful if anyone finding an inaccuracy or ambiguity while using this BritishStandard would inform the Secretary of the technical committee
28、responsible, the identity of which can be found on the inside front cover. Tel:02089969000. Fax:02089967400. BSI offers members an individual updating service called PLUS which ensures that subscribers automatically receive the latest editions of standards. Buying standards Orders for all BSI, inter
29、national and foreign standards publications should be addressed to Customer Services. Tel:02089969001. Fax:02089967001. In response to orders for international standards, it is BSI policy to supply the BSI implementation of those that have been published as BritishStandards, unless otherwise request
30、ed. Information on standards BSI provides a wide range of information on national, European and international standards through its Library and its Technical Help to Exporters Service. Various BSI electronic information services are also available which give details on all its products and services.
31、 Contact the Information Centre. Tel:02089967111. Fax:02089967048. Subscribing members of BSI are kept up to date with standards developments and receive substantial discounts on the purchase price of standards. For details of these and other benefits contact Membership Administration. Tel:020899670
32、02. Fax:02089967001. Copyright Copyright subsists in all BSI publications. BSI also holds the copyright, in the UK, of the publications of the internationalstandardization bodies. Except as permitted under the Copyright, Designs and Patents Act 1988 no extract may be reproduced, stored in a retrieva
33、l system or transmitted in any form or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This does not preclude the free use, in the course of implementing the standard, of necessary details such as symbols, and size, type or grade designations.
34、 If these details are to be used for any other purpose than implementation then the prior written permission of BSI must be obtained. If permission is granted, the terms may include royalty payments or a licensing agreement. Details and advice can be obtained from the Copyright Manager. Tel:02089967070.
