1、BSI Standards PublicationBS ISO 5611-1:2015Cartridges, type A, forindexable insertsPart 1: General survey, correlation anddetermination of dimensionsBS ISO 5611-1:2015 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 5611-1:2015.Together with BS ISO 5611-2, BS I
2、SO 5611-3, BS ISO 5611-4, BS ISO5611-5, BS ISO 5611-6, BS ISO 5611-7, BS ISO 5611-8, BS ISO 5611-9,BS ISO 5611-10, BS ISO 5611-11 and BS ISO 5611-12 it supersedesBS 4193-8:1997 (dual numbered as ISO 5611:1995) which will bewithdrawn upon publication of the rest of the parts in this series.The UK par
3、ticipation in its preparation was entrusted to TechnicalCommittee MTE/18, Tools tips and inserts for cutting applications.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport to include all the necessaryprovisions of a con
4、tract. Users are responsible for its correctapplication. The British Standards Institution 2015.ublished by BSI Standards Limited 2015ISBN 978 0 580 83608 4ICS 25.100.01Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the autho
5、rity of theStandards Policy and Strategy Committee on 30 November 2015.Amendments/corrigenda issued since publicationDate Text affectedBS ISO 5611-1:2015 ISO 2015Cartridges, type A, for indexable inserts Part 1: General survey, correlation and determination of dimensionsCartouches du type A, plaquet
6、tes amovibles Partie 1: Vue densemble, corrlation et dtermination des dimensionsINTERNATIONAL STANDARDISO5611-1First edition2015-11-01Reference numberISO 5611-1:2015(E)BS ISO 5611-1:2015ISO 5611-1:2015(E)ii ISO 2015 All rights reservedCOPYRIGHT PROTECTED DOCUMENT ISO 2015, Published in SwitzerlandAl
7、l rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on the internet or an intranet, without prior written permission. Permission can be requested f
8、rom either ISO at the address below or ISOs member body in the country of the requester.ISO copyright officeCh. de Blandonnet 8 CP 401CH-1214 Vernier, Geneva, SwitzerlandTel. +41 22 749 01 11Fax +41 22 749 09 47copyrightiso.orgwww.iso.orgBS ISO 5611-1:2015ISO 5611-1:2015(E)Foreword iv1 Scope . 12 No
9、rmative references 13 Survey. 14 Correlation of dimensions 44.1 Length l1and dimension f 44.2 Smallest possible internal diameter for operating 44.3 Correlation of the shank dimension and fastening of the shank . 55 Determination of dimensions . 75.1 Cutting edge corners 75.1.1 Cutting edge corner K
10、 .75.1.2 Theoretical cutting edge corner T 85.2 Corner radius rof master inserts 85.3 Length l195.4 Dimension f .95.5 Height h195.6 Tolerances 105.7 Dimension a 105.7.1 General. 105.7.2 Styles R and T 105.7.3 Styles K, S, W and Y .105.7.4 Values for dimension a 105.8 Correction values x and y 10Anne
11、x A (informative) Relationship between designations in ISO 5611 and ISO/TS 13399-2 and ISO/TS 13399-3 .15Bibliography .17 ISO 2015 All rights reserved iiiContents PageBS ISO 5611-1:2015ISO 5611-1:2015(E)ForewordISO (the International Organization for Standardization) is a worldwide federation of nat
12、ional standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. Interna
13、tional organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.The procedures used to develop this document and those intend
14、ed for its further maintenance are described in the ISO/IEC Directives, Part 1. In particular the different approval criteria needed for the different types of ISO documents should be noted. This document was drafted in accordance with the editorial rules of the ISO/IEC Directives, Part 2 (see www.i
15、so.org/directives).Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of any patent rights identified during the development of the document wil
16、l be in the Introduction and/or on the ISO list of patent declarations received (see www.iso.org/patents).Any trade name used in this document is information given for the convenience of users and does not constitute an endorsement.For an explanation on the meaning of ISO specific terms and expressi
17、ons related to conformity assessment, as well as information about ISOs adherence to the WTO principles in the Technical Barriers to Trade (TBT) see the following URL: Foreword - Supplementary informationThe committee responsible for this document is ISO/TC 29, Small tools, Subcommittee SC 9, Tools
18、with defined cutting edges, cutting items.This first edition of ISO 5611-1, together with ISO 5611-2, ISO 5611-3, ISO 5611-4, ISO 5611-5, ISO 5611-6. ISO 5611-7, ISO 5611-8, ISO 5611-9, ISO 5611-10, ISO 5611-11, and ISO 5611-12, cancels and replaces ISO 5611:1995, which has been technically revised.
19、ISO 5611 consists of the following parts, under the general title Cartridges, type A, for indexable inserts: Part 1: General survey, correlation and determination of dimensions Part 2: Style F Part 3: Style G Part 4: Style J Part 5: Style K Part 6: Style L Part 7: Style R Part 8: Style S Part 9: Sty
20、le T Part 10: Style U Part 11: Style W Part 12: Style Yiv ISO 2015 All rights reservedBS ISO 5611-1:2015INTERNATIONAL STANDARD ISO 5611-1:2015(E)Cartridges, type A, for indexable inserts Part 1: General survey, correlation and determination of dimensions1 ScopeThis part of ISO 5611 is general and is
21、 completed by ISO 5611-2 to ISO 5611-12. ISO 5611 applied for cartridges, type A, for indexable inserts and gives their styles in relation to their dimensions in accordance with ISO 5611-2 to ISO 5611-12. These cartridges are primarily intended for indexable inserts made of hard metal, ceramic or ot
22、her cutting materials to be used for turning operations.These kinds of cartridges are mainly clamped with one or two screws on the cartridges.Explanation of the designation code according to ISO 5608.2 Normative referencesThe following documents, in whole or in part, are normatively referenced in th
23、is document and are indispensable for its application. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies.ISO 5611-21), Cartridges, type A, for indexable inserts Part 2: Style FISO 5611-31), C
24、artridges, type A, for indexable inserts Part 3: Style GISO 5611-41), Cartridges, type A, for indexable inserts Part 4: Style JISO 5611-51), Cartridges, type A, for indexable inserts Part 5: Style KISO 5611-61), Cartridges, type A, for indexable inserts Part 6: Style LISO 5611-71), Cartridges, type
25、A, for indexable inserts Part 7: Style RISO 5611-81), Cartridges, type A, for indexable inserts Part 8: Style SISO 5611-91), Cartridges, type A, for indexable inserts Part 9: Style TISO 5611-101), Cartridges, type A, for indexable inserts Part 10: Style UISO 5611-111), Cartridges, type A, for indexa
26、ble inserts Part 11: Style WISO 5611-121), Cartridges, type A, for indexable inserts Part 12: Style Y3 SurveyTable 1 contains the survey of cartridges, type A, for indexable inserts which are standardized in ISO 5611-2 to ISO 5611-12 their corresponding letter symbols and the height h1of the cutting
27、 edge. The arrows in the figures show the primary direction of feed.1) To be published. ISO 2015 All rights reserved 1BS ISO 5611-1:2015ISO 5611-1:2015(E)Table 1 Survey of cartridges, type ADimensions in millimetresStyle SketchHeight of the cutting edgeh1Dimensions in ISO6 8 10 12 16 20 25F ISO 5611
28、-2 G ISO 5611-3 JISO 5611-4 K ISO 5611-5 L ISO 5611-6aIt is left to the manufacturers discretion or by agreement with edge angle r = 80 instead 100. = Standardized dimensions.blank = Not standardized.2 ISO 2015 All rights reservedBS ISO 5611-1:2015ISO 5611-1:2015(E)Style SketchHeight of the cutting
29、edgeh1Dimensions in ISO6 8 10 12 16 20 25RaaISO 5611-7 SaISO 5611-8 T ISO 5611-9 U ISO 5611-10W ISO 5611-11 Y ISO 5611-12 aIt is left to the manufacturers discretion or by agreement with edge angle r = 80 instead 100. = Standardized dimensions.blank = Not standardized.Table 1 (continued) ISO 2015 Al
30、l rights reserved 3BS ISO 5611-1:2015ISO 5611-1:2015(E)4 Correlation of dimensions4.1 Length l1and dimension fTable 2 contains the correlation between the length l1and the dimension f to their relevant height h1of the cutting edge and style of the cartridges, see also Figure 1.Figure 1 Cartridge sty
31、le KTable 2 Correlation of dimensionsDimensions in millimetresh1l1f 0080,for cartridge style for cartridge style0,08 F, G, J, K, L, R, T, U, Y W, S F, G, J, K, L, R, S, U, W, Y T6 25 21 8 5,58 32 28 10 610 50 44 14 912 55 47 20 1316 63 5325 1520 70 6025 100 87 32 204.2 Smallest possible internal dia
32、meter for operatingTable 3 contains the smallest possible internal diameter d1 minfor operating in relation with the relevant cartridge size h1, see also Figures 4 and 5.Table 3 Smallest possible internal diameter for operatingDimensions in millimetresh1 0,08 6 8 10 12 16 20 25d1min. 20 25 40 50 60
33、70 1004 ISO 2015 All rights reservedBS ISO 5611-1:2015ISO 5611-1:2015(E)4.3 Correlation of the shank dimension and fastening of the shankTable 4 contains the correlation between the shank dimensions and the bore diameter for fastening the shank and their relevant height h1of the cutting edge, see Fi
34、gures 2, 3, 4 and 5.Dimension l3applies to the adjusting screw in its mid-position, which is the reference point of the length l1, see 5.3. From this position, a minimum adjusting length of 0,4 mm shall be given in both directions.Figure 2 Shank having h1= 6 mm, 8 mm, 10 mm, 12 mm, 16 mm and 20 mmFi
35、gure 3 Shank having h1= 25 mm ISO 2015 All rights reserved 5BS ISO 5611-1:2015ISO 5611-1:2015(E)Figure 4 Sectional drawing AA for cartridges having h1= 6 mm, 8 mm, 10 mm or 12 mmFigure 5 Sectional drawing AA for cartridges having h1= 16 mm, 0 mm or 25 mmTable 4 Correlation of the shank dimension and
36、 fastening of the shankDimensions in millimetresh1b d2ae h2l2l3tFastening screw0,080 -0,2 H130 -0,2 min. 0,136 6 4 12 8,5 16 4,5 3,5 M3,58 8 4,5 17 11 21,5 6 4,5 M410 117 201526 85M612 16 20 616 20 9 25 25 32,510 M820 20 93030 37,5M825 25 11 35 59 M10aThe hole for fastening screws can be designed al
37、so as slotted hole at the manufacturers option.6 ISO 2015 All rights reservedBS ISO 5611-1:2015ISO 5611-1:2015(E)5 Determination of dimensions5.1 Cutting edge corners5.1.1 Cutting edge corner KThe specified point K is defined as follows:Consider plane Pf(assumed working plane) and Ps(tool cutting ed
38、ge plane) according to ISO 3002-1 for a selected point on the major cutting edge (for example point of tangency of major cutting edge with inscribed circle).a) For r 90, point K is defined as the intersection of plane Ps, a plane parallel to plane Pftangent to the corner radius and a plane containin
39、g the tool face A(see Figures 6 and 7).b) For r 90, point K is defined as the intersection of a plane parallel to plane Pftangent to the corner radius, a plane perpendicular to plane Pftangent to the corner radius and a plane containing the tool face A(see Figures 8 and 9).NOTE The position of the c
40、utting edge corner K is dependent from the corner radius rof the indexable insert.Figure 6 Cutting edge angle r 90, with transverse feedFigure 7 Cutting edge angle r 90, with longitudinal feed ISO 2015 All rights reserved 7BS ISO 5611-1:2015ISO 5611-1:2015(E)Figure 8 Cutting edge angle r 90, with tr
41、ansverse feedFigure 9 Cutting edge angle r 90, with longitudinal feed5.1.2 Theoretical cutting edge corner TThe intersection of the theoretical extensions of major cutting edge and minor cutting edge is considered as the theoretical cutting edge corner T, see Figures 6 to 9.NOTE The position of the
42、theoretical corner T is independent of the corner radius rof the indexable insert.5.2 Corner radius rof master insertsTable 5 contains the values of the corner radius rof the master insert (master gauge) used for the definition and testing of length l1, dimension f and height h1.The corner radius ro
43、f the master indexable insert is a function of the size of the indexable insert associated to cartridges and in Table 5 it is therefore related to the diameter of the inscribed circle.8 ISO 2015 All rights reservedBS ISO 5611-1:2015ISO 5611-1:2015(E)Table 5 Corner radius rof master insertsDimensions
44、 in millimetresdrNominal dimensionsa5,560,46,357,949,5250,812,715,8751,219,0525,4 2,4aFor the determination of the values of l1, f and the correction values x and y are derived from the accurate values of the corner radii r= 0,397 mm; 0,794 mm; 1,191 mm and 2,381 mm, which correspond to the inch dim
45、ensions.5.3 Length l1The length l1(for values see Table 2) is the distance between the specified point K and the shank end including adjustable screw in their mid-position (see Figure 1, Figures 6 to 9 and figures in Table 6), measured on a master indexable insert with corner radius rin accordance w
46、ith 5.2.For cartridges with indexable inserts with a corner radius rdeviating from Table 5, the modified length l1shall be determined with correction value x as shown in Figures 6 to 9.The correction value x (see Table 6) corresponds to the distance, measured parallel to the shank, between the speci
47、fied point K and the theoretical corner T.The modified length is obtained from the length l1given in Table 2 and the difference between the values x for the new corner radius and the corner radius given in Table 5.5.4 Dimension fDimension f (for values see Table 2) is the distance between the specif
48、ied point K and the rear backing surface of the cartridges (see Figure 1, Figures 6 to 9 and figures in Table 6), measured on a master insert with corner radius rin accordance with 5.2.For cartridges with inserts with a corner radius rdeviating from Table 5, the modified dimension f shall be determined with correction value y as shown in Figures 6 to 9.Correction value y corresponds to the distance between the specified point K and the theoretical cutting edge corner T, measured transverse to the shank.The modified dimension f is obtained from the value given in Table 2 and the difference b
