1、AMSC N/A FSC 5920 MIL-PRF-19207/16J 12 December 2013 SUPERSEDING MIL-F-19207/16H 24 April 2007 PERFORMANCE SPECIFICATION SHEET FUSEHOLDERS, EXTRACTOR POST TYPE, NONINDICATING, TYPES FHN26G1, FHN26G2, AND FHN26W This specification is approved for use by all departments and agencies of the Department
2、of Defense. The requirements for acquiring the product described herein shall consist of this specification sheet and MIL-PRF-19207. Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Min Max A .670 .710 17.02 18.03 F - 2.340 - 59.44 B .650 (REF) 16.51 (REF) G - .600 - 15.24 C .680 .690 17.27 17.53
3、 H .455 .465 11.56 11.81 D .480 .520 12.70 13.21 J .475 .480 12.07 12.19 E .112 .118 2.81 3.00 K .500 .510 12.70 12.95 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general. 3. Unless otherwise specified, tolerances are 0.02 (0.51 mm) for two-place
4、decimals and 0.005 (0.13 mm) for three-place decimals. 4. The location (on the fuseholder body) of the manufacturers identification and type designation is optional. 5. The shape of the above fuseholder and knob marking are shown for information only. Slight deviations from this outline drawing and/
5、or the knob marking, which do not alter the functional aspect of the device, are acceptable. FIGURE 1. Type FHN26G1. INCH-POUND Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/16J 2 Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Mi
6、n Max A .440 .452 11.18 11.48 F .780 (REF) 19.50 (REF) B .670 .710 17.02 18.03 G - 2.090 - 53.09 C .090 .130 2.29 3.30 H .685 .695 17.40 17.53 D .410 .450 10.41 11.43 J .475 .480 12.07 12.19 E - .060 - 1.52 K .500 .510 12.70 12.95 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nea
7、rest 0.01 mm) are given for general. 3. Unless otherwise specified, tolerances are 0.02 (0.51 mm) for two-place decimals and 0.005 (0.13 mm) for three-place decimals. 4. The location (on the fuseholder body) of the manufacturers identification and type designation is optional. 5. The shape of the ab
8、ove fuseholder and knob marking are shown for information only. Slight deviations from this outline drawing and/or the knob marking, which do not alter the functional aspect of the device, are acceptable. FIGURE 2. Type FHN26G2 Provided by IHSNot for ResaleNo reproduction or networking permitted wit
9、hout license from IHS-,-,-MIL-PRF-19207/16J 3 Ltr Inches mm Ltr Inches mm Min Max Min Max Min Max Min Max A .932 .942 23.67 23.93 F .558 .567 14.17 14.40 B .810 (REF) 20.57 (REF) G .920 .960 23.37 24.38 C .350 390 8.89 9.91 H .505 .513 12.83 13.03 D - 2.180 - 55.37 J .625 .635 15.88 16.13 E .100 .14
10、0 2.54 3.56 K .570 .575 14.48 14.61 NOTES: 1. Dimensions are in inches. 2. Metric equivalents (to the nearest 0.01 mm) are given for general. 3. Unless otherwise specified, tolerances are 0.02 (0.51 mm) for two-place decimals and 0.005 (0.13 mm) for three-place decimals. 4. The location (on the fuse
11、holder body) of the manufacturers identification and type designation is optional. 5. The shape of the above fuseholder and knob marking are shown for information only. Slight deviations from this outline drawing and/or the knob marking, which do not alter the functional aspect of the device, are ac
12、ceptable. 6. Rear terminal for type FHN26W fuseholders shall have the option of being centered or located at the edge of the fuseholder body. FIGURE 3. Type FHN26W. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/16J 4 REQUIREMENTS Inte
13、rface and physical dimensions: See figures 1, 2, and 3. Cap and body molding material: Molding materials shall be selected to enable the fuseholder to meet the performance requirements of this specification. It is recommended that types MAI-60, GDI-30F or SDG-F of American Society for Testing and Ma
14、terials ASTM-D5948 be considered for meeting the cap and body molding material requirements of this specification. Gaskets and O-rings: It is recommended that class 3 silicone rubber of A-A-59588 (Rubber, Silicone), be considered for use in meeting the gasket and o-ring material requirements of this
15、 specification. Fuse accommodation: Ferrule type: Size: 0.250 inch (6.35 mm) diameter, 1.250 inches (31.75 mm) length. Style: F02: MIL-PRF-15160/2, F03: MIL-PRF-15160/3 and FM09: MIL-PRF-23419/9. (or equivalent size and style) Poles: One. Rating: 30 amperes, 250 volts maximum. Panel thickness: 0.187
16、 inch (4.76 mm) maximum. Nonindicating. Lamp series resistor: None. Terminals: Solder lug type. Enclosure: FHN26G1 and FHN26G2 - Dripproof. FHN26W - Watertight. Test fuses: Temperature rise: F03A125V30A of MIL-PRF-15160/3. Short circuit: F03A250V15A of MIL-PRF-15160/3. Mechanical shock: Method I of
17、MIL-PRF-19207. Terminal strength: 5 pounds. Torque: Mounting - 20 inch-pounds for FHN26G1 and FHN26G2; 30 inch-pounds for FHN26W. Salt spray (corrosion): Test condition B. Part or Identifying Number (PIN): See table I. TABLE I. Superseding PIN Superseded military part number FHN26G1 M19207/16-001 FH
18、N26G2 M19207/16-002 FHN26W M19207/16-003 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-PRF-19207/16J 5 Referenced documents. In addition to MIL-PRF-19207, this document references the following: MIL-PRF-15160/2 MIL-PRF-15160/3 MIL-PRF-23419/9 A
19、STM-D5948 A-A-59588 The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors ar
20、e cautioned to evaluate the requirements of this document based on the entire content irrespective of the marginal notations and relationship to the last previous issue. Custodians: Preparing Activity: Army - CR DLA - CC Navy - SH Air force - 85 (Project 5920-2012-062) DLA - CC Review activities: Ar
21、my - AR, AT, CR4, MI Navy - AS, OS Air Force - 19, 70, 71, 84, 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.dla.mil. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
