1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Change drawing CAGE number to 67268. Page 13; note 1/ tr 1.5 ns should be tr 15 ns. Page 15; correct vendor part number. 87-11-20 R. P. Evans B Update to reflect latest changes in format and requirements. Editorial changes throughout. -les 01-10-
2、11 Raymond Monnin C Update drawing to current requirements. Editorial changes throughout. - gap 09-01-23 Robert M. Heber CURRENT CAGE CODE IS 67268. The original first sheet of this drawing has been replaced. REV SHET REV SHET REV STATUS REV C C C C C C C C C C C C C OF SHEETS SHEET 1 2 3 4 5 6 7 8
3、9 10 11 12 13 PMIC N/A PREPARED BY Monica Grosel DEFENSE SUPPLY CENTER COLUMBUS STANDARD MICROCIRCUIT DRAWING CHECKED BY D. A. DiCenzo COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY N. A. Hauck MICROCIRCUIT, DIGITAL, BIPOLAR, THREE-S
4、TATE PRIORITY ENCODER, MONOLITHIC AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 87-04-14 SILICON AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 14933 5962-87542 SHEET 1 OF 13 DSCC FORM 2233 APR 97 5962-E364-08 Provided by IHSNot for ResaleNo reproduction or networking permitted without
5、 license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing describes device requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits
6、in accordance with MIL-PRF-38535, appendix A. 1.2 Part or Identifying Number (PIN). The complete PIN is as shown in the following example: 5962-87542 01 R X Drawing number Device type (see 1.2.1) Case outline(see 1.2.2) Lead finish(see 1.2.3)1.2.1 Device type(s). The device type(s) identify the circ
7、uit function as follows: Device type Generic number Circuit function 01 25LS2513 or 29LS13 Three-state priority checker 1.2.2 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or GDIP2-T20
8、20 Dual-in-line S GDFP2-F20 or GDFP3-F20 20 Flat 2 CQCC1-N20 20 Square chip carrier 1.2.3 Lead finish. The lead finish is as specified in MIL-PRF-38535, appendix A. 1.3 Absolute maximum ratings. Supply voltage (VCC) -0.5 V dc to +7.0 V dc Input voltage range . -1.5 V dc to +7.0 V dc Storage temperat
9、ure range . -65C to +150C Maximum power dissipation (PD) 1/ 0.60 W Lead temperature (soldering, 10 seconds) +300C Thermal resistance, junction-to-case (JC) See MIL-STD-1835 Junction temperature (TJ) +150C DC input current -30 mA to +5.0 mA DC output current, into output . +30 mA 1.4 Recommended oper
10、ating conditions. Supply voltage range (VCC) . +4.5 V dc to 5.5 V dc maximum Minimum high level input voltage (VIH) 2.0 V Maximum low level input voltage (VIL) . 0.7 V Ambient operating temperature range (TA) . -55C to +125C _ 1/ Must withstand the added PDdue to short circuit test (e.g. IOS). Provi
11、ded by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, s
12、tandards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - In
13、tegrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings.
14、MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Order of precedence. In the event of a conflict
15、 between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requir
16、ements shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. Product built to this drawing that is produced by a Qualified Manufacturer Listing (QML) certified and qualified manufacturer or a manufacturer who has been granted transitional ce
17、rtification to MIL-PRF-38535 may be processed as QML product in accordance with the manufacturers approved program plan and qualifying activity approval in accordance with MIL-PRF-38535. This QML flow as documented in the Quality Management (QM) plan may make modifications to the requirements herein
18、. These modifications shall not affect form, fit, or function of the device. These modifications shall not affect the PIN as described herein. A “Q“ or “QML“ certification mark in accordance with MIL-PRF-38535 is required to identify when the QML flow option is used. 3.2 Design, construction, and ph
19、ysical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535, appendix A and herein. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.2 herein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 1.
20、 3.2.3 Truth tables. The truth tables shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Test circuits and switching waveforms. The test circuit and switching waveforms shall be as specified on figure 4. 3.3 Electrical performance chara
21、cteristics. Unless otherwise specified herein, the electrical performance characteristics are as specified in table I and shall apply over the full ambient operating temperature range. 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified in table II. Th
22、e electrical tests for each subgroup are described in table I. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM
23、 2234 APR 97 3.5 Marking. Marking shall be in accordance with MIL-PRF-38535, appendix A. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitations
24、, the manufacturer has the option of not marking the “5962-“ on the device. 3.5.1 Certification/compliance mark. A compliance indicator “C” shall be marked on all non-JAN devices built in compliance to MIL-PRF-38535, appendix A. The compliance indicator “C” shall be replaced with a “Q“ or “QML“ cert
25、ification mark in accordance with MIL-PRF-38535 to identify when the QML flow option is used. 3.6 Certificate of compliance. A certificate of compliance shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6 herein). The certificate of co
26、mpliance submitted to DSCC-VA prior to listing as an approved source of supply shall affirm that the manufacturers product meets the requirements of MIL-PRF-38535, appendix A and the requirements herein. 3.7 Certificate of conformance. A certificate of conformance as required in MIL-PRF-38535, appen
27、dix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change. Notification of change to DSCC-VA shall be required for any change that affects this drawing. 3.9 Verification and review. DSCC, DSCCs agent, and the acquiring activity retain the option to
28、review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 4. VERIFICATION 4.1 Sampling and inspection. Sampling and inspection procedures shall be in accordance with MIL-PRF-38535, appendix A. 4.2 Sc
29、reening. Screening shall be in accordance with method 5004 of MIL-STD-883, and shall be conducted on all devices prior to quality conformance inspection. The following additional criteria shall apply: a. Burn-in test, method 1015 of MIL-STD-883. (1) Test condition C or D. The test circuit shall be m
30、aintained by the manufacturer under document revision level control and shall be made available to the preparing or acquiring activity upon request. The test circuit shall specify the inputs, outputs, biases, and power dissipation, as applicable, in accordance with the intent specified in method 101
31、5 of MIL-STD-883. (2) TA= +125C, minimum. b. Interim and final electrical test parameters shall be as specified in table II herein, except interim electrical parameter tests prior to burn-in are optional at the discretion of the manufacturer. Provided by IHSNot for ResaleNo reproduction or networkin
32、g permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test Symbol Conditions -55C TA+125C Group A subgroups Limi
33、ts Unit unless otherwise specified Min Max High level output voltage VOHA1IOH= -1.0 mA 1, 2, 3 2.4 V VCC= +4.5 V, VIN= 2.0 V or 0.7 V E0IOH= -440 A 1, 2, 3 2.5 V Low level output voltage VOLIOL= 4.0 mA 1, 2, 3 0.4 V IOL= 8.0 mA 1, 2, 3 0.45 V VCC= +4.5 V, VIN= 2.0 V or 0.7 V IOL= 12.0 mA An outputs
34、1, 2, 3 0.5 V Input clamp voltage VI CVCC= +4.5 V, IIN= -18 mA 1, 2, 3 -1.5 V High level input current II H1 VCC= +5.5 V, VIN= 2.7 V E1, G1, G2, G3, G4, G5, I01, 2, 3 20.0 A All others 1, 2, 3 40.0 A II H2 VCC= +5.5 V, VIN= 7.0 V E1, G1, G2, G3, G4, G5, I01, 2, 3 100 A All others 1, 2, 3 200 A Low l
35、evel input current IILVCC= +5.5 V, VIN= 0.4 V E1, G1, G2, G3, G4, G5, I01, 2, 3 -0.4 mA All others 1, 2, 3 -0.8 mA Output short circuit current IOSVCC= +5.5 V, VOUT= 0.0 V 1/ 1, 2, 3 -15 -85 mA Supply current ICC VCC= +5.5 V, Input to outputs open 1, 2, 3 24 mA Off-state current IOZH VCC= +5.5 V, VO
36、UT= 2.4 V 1, 2, 3 20 A Off-state current IOZL VCC= +5.5 V, VOUT= 0.4 V 1, 2, 3 -20 A Functional tests See 4.3.1c 7, 8 Propagation delay time, tPLH1 CL= 15 pF 2/ 9 25 ns I1to An(in phase) CL = 50 pF 3/ 9, 10, 11 37 ns tPHL1 RL1= 5 k RL2= 2 k (See figure 4) CL= 15 pF 2/ 9 25 ns L= 50 pF 3/ 9, 10, 11 3
37、4 ns See footnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Elect
38、rical performance characteristics - Continued. Test Symbol Conditions -55C TA+125C Group A subgroups Limits Unit unless otherwise specified Min Max Propagation delay time, tPLH2 CL= 15 pF 2/ 9 17 ns I1to An(out phase) CL = 50 pF 3/ 9, 10, 11 27 ns tPHL2 CL= 15 pF 2/ 9 18 ns RL1= 5 k RL2= 2 k (See fi
39、gure 4) CL= 50 pF 3/ 9, 10, 11 25 ns Propagation delay time, tPLH3 CL= 15 pF 2/ 9 11 ns I1to E0RL= 2 k (See figure 4) CL= 50 pF 3/ 9, 10, 11 18 ns tPHL3 CL= 15 pF 2/ 9 36 ns L= 50 pF 3/ 9, 10, 11 60 ns Propagation delay time, tPLH4 L= 15 pF 2/ 9 17 ns E1to E0CL = 50 pF 3/ 9, 10, 11 21 ns tPHL4 L= 15
40、 pF 2/ 9 34 ns L= 50 pF 3/ 9, 10, 11 57 ns Propagation delay time, tPLH5 CL= 15 pF 2/ 9 18 ns E1to AnCL = 50 pF 3/ 9, 10, 11 25 ns tPHL5 CL= 15 pF 2/ 9 21 ns RL1= 5 k RL2= 2 k (See figure 4) CL= 50 pF 3/ 9, 10, 11 32 ns Propagation delay time, tPZH1 CL= 15 pF 2/ 9 40 ns G1or G2to AnL= 50 pF 3/ 9, 10
41、, 11 49 ns tPZL1 L= 15 pF 2/ 9 37 ns CL= 50 pF 3/ 9, 10, 11 49 ns Propagation delay time, tPZH2 L= 15 pF 2/ 9 30 ns G3, G4, G5to AnL = 50 pF 3/ 9, 10, 11 43 ns tPZL2 CL= 15 pF 2/ 9 27 ns L= 50 pF 3/ 9, 10, 11 43 ns Propagation delay time, tPHZ1 2/ 9 27 ns G1or G2to An3/ 9, 10, 11 40 ns tPLZ1 2/ 9 28
42、 ns CL= 5 pF RL1= 5 k RL2= 2 k (See figure 4) 3/ 9, 10, 11 40 ns Propagation delay time, tPHZ2 2/ 9 24 ns G3, G4, G5to An3/ 9, 10, 11 35 ns tPLZ2 / 9 27 ns / 9, 10, 11 35 ns 1/ Not more than one output should be shorted at a time, and the duration of the short circuit condition should not exceed one
43、 second. 2/ VCC= 5.0 V. 3/ VCC= +4.5 V to + 5.5 V. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97
44、 Device type 01 Case outlines R, S, and 2 Terminal number Terminal symbol 1 I4 2 I5 3 I6 4 I7 5 E16 A27 A18 A0 9 G4 10 GND11 G3 12 G113 G2 14 G515 I116 I217 I318 I019 E020 VCC FIGURE 1. Terminal connections. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IH
45、S-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 8 DSCC FORM 2234 APR 97 Inputs Outputs E1I0I1I2I3I4I5I6I7A0A1A2 E0H X X X X X X X X L L L H L H H H H H H H H L L L L L X X X X X X X L H H H H L X X X X X X L H L H
46、H H L X X X X X L H H H L H H L X X X X L H H H L L H H L X X X L H H H H H H L H L X X L H H H H H L H L H L X L H H H H H H H L L H L L H H H H H H H L L L H H = High voltage level L = Low voltage level X = Dont care For G1= H, G2= H, G3= L, G4= L, G5= L G1 G2G3G5G5A0 A1 A2 H H L L L ENABLED L X X
47、 X X Z Z Z X L X X X Z Z Z X X H X X Z Z Z X X X H X Z Z Z X X X X H Z Z Z Z = HIGH impedance FIGURE 2. Truth tables. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUM
48、BUS, OHIO 43218-3990 REVISION LEVEL C SHEET 9 DSCC FORM 2234 APR 97 FIGURE 3. Logic diagram. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-87542 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 10 DSCC FORM 2234 APR 97 FIGURE 4. Test circuits and switching waveforms. Provided by IHSNot for ResaleNo reproduction or networking permitted without lice
