FORD FLTM BN 157-01-2001 DETERMINATION OF LEATHER SOFTNESS《皮革柔软度的测定》.pdf

上传人:周芸 文档编号:747284 上传时间:2019-01-14 格式:PDF 页数:3 大小:178.96KB
下载 相关 举报
FORD FLTM BN 157-01-2001 DETERMINATION OF LEATHER SOFTNESS《皮革柔软度的测定》.pdf_第1页
第1页 / 共3页
FORD FLTM BN 157-01-2001 DETERMINATION OF LEATHER SOFTNESS《皮革柔软度的测定》.pdf_第2页
第2页 / 共3页
FORD FLTM BN 157-01-2001 DETERMINATION OF LEATHER SOFTNESS《皮革柔软度的测定》.pdf_第3页
第3页 / 共3页
亲,该文档总共3页,全部预览完了,如果喜欢就下载吧!
资源描述

1、 FORD LABORATORY TEST METHOD BN 157-01 Date Action Revisions 2001 11 30 Activated J W Williams Printed copies are uncontrolled Page 1 of 3 Copyright 2001, Ford Global Technologies, Inc. DETERMINATION OF LEATHER SOFTNESS Application This test method defines a procedure for the determination of leathe

2、r softness, applicable to hides and cut parts, in all leather types, used in trim and seating applications. Apparatus and Materials Required ST-300 Leather Softness Tester Using 25mm diameter (nominal) aperture (see diagram in Appendix A). Supplier: MSA Engineering Systems Limited 41 Lower Slack Wai

3、nstalls Halifax West Yorkshire HX2 7TJ United Kingdom Sole worldwide agents for the ST-300 Leather Softness Tester. Conditioning and Test Conditions All test values indicated herein are based on material conditioned in a controlled atmosphere of 23 +/- 2 C and 50 +/- 5 % relative humidity for not le

4、ss than 24 h prior to testing and tested under the same conditions unless otherwise specified. Specimens Cut parts or full hides may be used; sampling should be representative as detailed in the Calculation and Report section. Procedure 1. The leather sample is placed over the circular aperture, ens

5、uring that the aperture is completely covered to allow effective clamping. FORD LABORATORY TEST METHOD BN 157-01 Page 2 of 3 Copyright 2001, Ford Global Technologies, Inc. 2. Lower the top arm using the operating lever to retract the load-pin. Press down on the lever, so locking the leather in posit

6、ion, with an audible click. 3. Release the operating lever, allowing the load-pin to lower onto the leather and to apply a force of 4.91N (a 500g mass). 4. The load-pin deflects the leather; this deflection is displayed on the dial gauge in millimeters. 5. Allow a minimum dwell time of 30 seconds th

7、en allow the reading on the gauge to stabilize and record. 6. Press the top arm release button to release the clamp, to allow the removal of the leather. Note: At the beginning of each test period, the zero correction should be ascertained. Place the rigid metal plate supplied with the gauge on the

8、bottom leather clamp and follow steps 2-5 above. Adjust gauge to read zero in this position or add zero correction measured to the results obtained on test samples. Calculation and Report Cut Parts Two measurements shall be taken, one each at opposite ends of the long axis of the part. The reported

9、value for the part shall be the mean of the two measurements. Acceptance criteria will be detailed on the relevant Material Specification or on the Engineering Drawing. Full Hides Five measurements shall be taken around the hide, in the following locations: The reported value shall be the mean of th

10、ese five measurements. Acceptance criteria will be detailed in the relevant Material Specification or on the Engineering Drawing. FORD LABORATORY TEST METHOD BN 157-01 Page 3 of 3 Copyright 2001, Ford Global Technologies, Inc. Appendix A The ST-300 Softness Tester Cross Sectional View of the Working Head of the Apparatus

展开阅读全文
相关资源
猜你喜欢
  • BS EN 14223-2017 Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Determination of water absorption《防水用软.pdf BS EN 14223-2017 Flexible sheets for waterproofing Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles Determination of water absorption《防水用软.pdf
  • BS EN 14224-2010 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of crack bridging ab.pdf BS EN 14224-2010 Flexible sheets for waterproofing - Waterproofing of concrete bridge decks and other concrete surfaces trafficable by vehicles - Determination of crack bridging ab.pdf
  • BS EN 14225-4-2005 Diving suits - Part 4 One atmosphere suits (ADS) - Human factors requirements and test methods《潜水服 第4部分 一个大气压的潜水服(ADS) 人类因素要求和试验方法》.pdf BS EN 14225-4-2005 Diving suits - Part 4 One atmosphere suits (ADS) - Human factors requirements and test methods《潜水服 第4部分 一个大气压的潜水服(ADS) 人类因素要求和试验方法》.pdf
  • BS EN 14227-1-2013 Hydraulically bound mixtures Specifications Cement bound granular mixtures《液压粘结混合物 规范 水泥粘粘结颗粒混合物》.pdf BS EN 14227-1-2013 Hydraulically bound mixtures Specifications Cement bound granular mixtures《液压粘结混合物 规范 水泥粘粘结颗粒混合物》.pdf
  • BS EN 14227-2-2013 Hydraulically bound mixtures Specifications Slag bound granular mixtures《液力粘结混合料 规格 矿渣粘结混合料》.pdf BS EN 14227-2-2013 Hydraulically bound mixtures Specifications Slag bound granular mixtures《液力粘结混合料 规格 矿渣粘结混合料》.pdf
  • BS EN 14227-3-2013 Hydraulically bound mixtures Specifications Fly ash bound granular mixtures《液力粘结混合料 规格 飞灰粘结混合料》.pdf BS EN 14227-3-2013 Hydraulically bound mixtures Specifications Fly ash bound granular mixtures《液力粘结混合料 规格 飞灰粘结混合料》.pdf
  • BS EN 14227-4-2013 Hydraulically bound mixtures Specifications Fly ash for hydraulically bound mixtures《液力粘结混合料 规格 液力粘结混合料用飞灰》.pdf BS EN 14227-4-2013 Hydraulically bound mixtures Specifications Fly ash for hydraulically bound mixtures《液力粘结混合料 规格 液力粘结混合料用飞灰》.pdf
  • BS EN 14227-5-2013 Hydraulically bound mixtures Specifications Hydraulic road binder bound granular mixtures《液力粘结混合料 规格 液力道路粘结混合料》.pdf BS EN 14227-5-2013 Hydraulically bound mixtures Specifications Hydraulic road binder bound granular mixtures《液力粘结混合料 规格 液力道路粘结混合料》.pdf
  • BS EN 14229-2010 Structural timber Wood poles for overhead lines《木结构 架空线用木杆》.pdf BS EN 14229-2010 Structural timber Wood poles for overhead lines《木结构 架空线用木杆》.pdf
  • 相关搜索

    当前位置:首页 > 标准规范 > 国际标准 > 其他

    copyright@ 2008-2019 麦多课文库(www.mydoc123.com)网站版权所有
    备案/许可证编号:苏ICP备17064731号-1