1、AEROSPACE STANDARD PIN, EXPANSION - CRES, 303, LONG, UNS S30300 AS3130Copyright 2014 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or oth
2、erwise, without the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1981-02REAFFIRMED 2006-05 REVISED 2014-01THIRD ANGLE
3、PROJECTION CUSTODIAN: E-25 REV.BFEDERAL SUPPLY CLASS 5315 AS3130SHEET 1 OF 2REV. BPROCUREMENT SPECIFICATION: NONESAE Technical Standards Board Rules provide that: “This report ispublishedby SAE toadvance thestate of technicalandengineering sciences. Theuse ofthis report is entirely voluntary, andits
4、 applicability and suitability forany particular use,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised, reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments
5、andsuggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS3130BRATIONALE THIS IS A LIMITED SCOPE REVISION. REVISED CLEANING REQUIREMENTS (NOTE 3) FOR CONFORMANCE TO AMS2700 OR ASTM A967/A967M. FIGURE 1 TABLE 1 PART NUMBER
6、S AND DIMENSIONS AEROSPACE STANDARD PART NUMBER /8/MANUFACTURERSPART NUMBER /8/ANOM BNOM CMAXDNOM ENOM FNOM APPROX MASSLB/100 AS3130-03 PLGA1566030A .175 .118 .032 .0208 (a) (a) .047 AS3130-04 PLGA1876030A .181 .154 .040 .0417 10 .138 .084 AS3130-05 PLGA2186030A .218 .181 .040 .0208 10 .165 .144AS31
7、30-06 PLGA2506030A .265 .212 .040 .0417 10 .192 .239 AS3130-07 PLGA2816030A .280 .244 .040 .0313 (a) (a) .339 AS3130-08 PLGA3436030A .335 .308 .060 .0208 (a) (a) .652 AS3130-09 PLGA4066030A .397 .370 .060 .0208 (a) (a) 1.128AS3130-10 PLGA4686030A .460 .433 .060 .0208 (a) (a) 1.802 AS3130-11 PLGA5316
8、030A .522 .495 .060 .0156 (a) (a) 2.705AS3130-12 PLGA6566030A .590 .601 .060 .0156 10 .572 4.517 (a) .01-.02 RADIUS INSTEAD OF A CHAMFER. AEROSPACE STANDARD AS3130SHEET 2 OF 2REV. BPIN, EXPANSION - CRES, 303, LONG, UNS S30300 NOTES: 1. MATERIAL: 303 CRES BAR PER AMS5640, TYPE 1, UNS S30300. 2. HEAT
9、TREAT: PER AMS5640. 3. CLEANING: FINISHED PARTS SHALL BE DEGREASED AND PASSIVATED PER ASTM A967/A967M OR AMS2700. A SOLUTION CONTAINING SODIUM DICHROMATE AND NOT LESS THAN 20% BY VOLUME OF NITRIC ACID MUST BE USED. A CITRIC ACID METHOD MAY BE USED AS AN ALTERNATIVE IF REQUESTED BY THE PROCURING ACTI
10、VITY AND THE SUPPLIER AGREES. 4. PINS ARE PREWAXED TO AID DRIVING. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, SURFACES TO BE 250 MICROINCHES Ra. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONS IN INCHES. UNLESS OTHERWI
11、SE SPECIFIED, TOLERANCES: ANGULAR DIMENSIONS 2 DEGREES. /8/ MARK AS3130-( ) PART NUMBER AND MANUFACTURERS PART NUMBER ON PACKAGE IN ACCORDANCE WITH AS478, METHOD 37. 9. USE WITH AS3129 PLUGS. SEE AIR3277 INSTALLATION PROCEDURES. 10. DIMENSIONING AND TOLERANCING: PER ASME Y14.5M-1994. 11. DO NOT USE
12、UNASSIGNED PART NUMBERS. 12. SEE AS3586 FOR PLUG AND PIN SET OF PARTS. 13. AS, AIR, AND AMS ARE SAE INTERNATIONAL PUBLICATIONS. ASME IS AN AMERICAN SOCIETY OF MECHANICAL ENGINEERS PUBLICATION. 14. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE
13、TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS, NOR IN DOCUMENTS
14、 THAT CONTAIN EDITORIAL CHANGES ONLY. APPROVED SOURCE OF SUPPLY: THE LEE CO WESTBROOK, CT FEDERAL SUPPLY CODE FOR MANUFACTURERS NO 92555. ONLY THE ITEM DESCRIBED ON THIS DRAWING WHEN PROCURED FROM THE VENDOR LISTED HEREON IS APPROVED FOR USE IN THE APPLICATIONS SPECIFYING THIS AEROSPACE STANDARD IDE
15、NTIFICATION NUMBER. A SUBSTITUTE ITEM SHALL NOT BE USED WITHOUT PRIOR TESTING AND APPROVAL BY THE DESIGN ACTIVITY RESPONSIBLE FOR THE APPLICATION. IDENTIFICATION OF THE APPROVED SOURCE HEREON IS NOT TO BE CONSTRUED AS A GUARANTEE OF PRESENT OR CONTINUED AVAILABILITY AS A SOURCE OF SUPPLY FOR THE ITEM DESCRIBED ON THE DRAWING.
