1、 AEROSPACE STANDARD WIRE, RETAINING FOR RETAINED NUT AS4341Copyright 2015 SAE International All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, wit
2、hout the prior written permission of SAE. TO PLACE A DOCUMENT ORDER: Tel: 877-606-7323 (inside USA and Canada) Tel: +1 724-776-4970 (outside USA) Fax: 724-776-0790 Email: CustomerServicesae.org SAE WEB ADDRESS: http:/www.sae.org ISSUED 1993-08REAFFIRMED2007-10 REVISED 2015-02THIRD ANGLE PROJECTION C
3、USTODIAN: G-3/G-3B REV.A FEDERAL SUPPLY CLASS 4730 AS4341 SHEET 1 OF 2 REV. A PROCUREMENT SPECIFICATION: NONE /3/SAE Technical Standards Board Rules provide that: “This report ispublished by SAE toadvance thestate of technicalandengineering sciences. Theuse ofthisreport is entirelyvoluntary, andits
4、applicability and suitability forany particularuse,including any patent infringement arising therefrom, isthe soleresponsibilityofthe user.”SAE reviews eachtechnicalreport at least every five years at which time itmay berevised,reaffirmed, stabilized, orcancelled. SAE invites yourwrittencomments and
5、suggestions. SAE values your input. To provide feedbackon this Technical Report, please visit http:/www.sae.org/technical/standards/AS4341A 04 .250 1.094 .075-.085 .0016906 .375 1.453 .075-.085 .0022508 .500 2.000 .086-.096 .0040110 .625 2.326 .086-.096 .0046612 .750 2.859 .115-.135 .0108016 1.000 3
6、750 .115-.135 .0142020 1.250 4.750 .115-.135 .0180024 1.500 5.500 .115-.135 .0208028 1.750 6.750 .115-.135 .0255032 2.000 7.500 .115-.135 .02830LB/EA MAXBASIC NUMBER AS4341/9/ SIZE CODE(NOMINAL TUBE SIZE)BA .016RATIONALE ADDED A DASH IN THE PART NUMBER EXAMPLE TO NOTE /9/ AND SPECIFIED A PASSIVATIO
7、N TYPE FOR FINISH TO NOTE /2/. FIGURE 1 - WIRE, RETAINING TABLE 1 - DIMENSIONS AND WEIGHTS AEROSPACE STANDARD AS4341 SHEET 2 OF 2 REV. A WIRE, RETAINING FOR RETAINED NUT NOTES: 1. MATERIAL: CORROSION RESISTANT STEEL WIRE, TYPE 302, 304, OR 305 PER ASTM A580 ANNEALED. 2. FINISH: PASSIVATE PER AMS2700
8、 TYPE 6 OR 7. /3/ PROCUREMENT SPECIFICATION: KSC-F-124 JOHN F. KENNEDY SPACE CENTER, NASA, SPECIFICATION FOR FITTING (PRESSURE CONNECTIONS), FLUID FLARE. 4. INTERPETATION OF DRAWING PER AS4296. 5. SURFACE TEXTURE: SYMBOLS PER ASME Y14.36M. REQUIREMENTS PER ASME B46.1. UNLESS OTHERWISE SPECIFIED, MAC
9、HINED SURFACES ARE TO 125 MICROINCHES Ra. 6. BREAK EDGES .003 TO .015 UNLESS OTHERWISE SPECIFIED. 7. DIMENSIONING AND TOLERANCING: ANSI Y14.5M-1982. 8. DIMENSIONS IN INCHES. UNLESS OTHERWISE SPECIFIED, TOLERANCES: LINEAR DIMENSIONS .016, ANGULAR DIMENSIONS .5. /9/ EXAMPLE OF PART NUMBER: AS4341 - 08
10、 BASIC PART NUMBER: NOMINAL TUBE SIZE IN .062 INCH INCREMENTS (08=.500) 10. A CHANGE BAR (l) LOCATED IN THE LEFT MARGIN IS FOR THE CONVENIENCE OF THE USER IN LOCATING AREAS WHERE TECHNICAL REVISIONS, NOT EDITORIAL CHANGES, HAVE BEEN MADE TO THE PREVIOUS ISSUE OF THIS DOCUMENT. AN (R) SYMBOL TO THE LEFT OF THE DOCUMENT TITLE INDICATES A COMPLETE REVISION OF THE DOCUMENT, INCLUDING TECHNICAL REVISIONS. CHANGE BARS AND (R) ARE NOT USED IN ORIGINAL PUBLICATIONS NOR IN DOCUMENTS THAT CONTAIN EDITORIAL CHANGES ONLY.
