1、 J-STD-025-B-1 September 2006 Lawfully Authorized Electronic Surveillance (LAES) Addendum 1-Addition of Mobile Equipment Identifier (MEID) ANSI/J-STD-025-B-1-2006 APPROVED: SEPTEMBER 8, 2006 REAFFIRMATION: APRIL 12, 2012 JOINT STANDARDS Joint Standards and Publications are adopted in accordance with
2、 the American National Standards Institute (ANSI) patent policy. By such action, the Telecommunications Industry Association or the Alliance for Telecommunications Industry Solutions does not assume any liability to any patent owner, nor does it assume any obligation whatever to parties adopting the
3、 Standard or Publication. This Standard does not purport to address all safety problems associated with its use or all applicable regulatory requirements. It is the responsibility of the user of this Standard to establish appropriate safety and health practices and to determine the applicability of
4、regulatory limitations before its use. This standard was developed under Project No. SP-3-4465-UGRV2-RF1, formulated under the cognizance of the TIA TR-45 Committee on Mobile Telephone (703)907-7700; Fax: (703)907-7727 or by email to receptiontiaonline.org. This document was coordinated between ATIS
5、 and TIA. A Word from TIA: TIA Engineering Standards and Publications are designed to serve the public interest through eliminating misunderstanding between manufacturers and purchasers, facilitating interchangeability and improvement of products, and assisting the purchaser in selecting and obtaini
6、ng with minimum delay the proper product for his/her particular need. Existence of such Standards and Publications shall not be in any respect preclude any member or nonmember of TIA from manufacturing or selling products not conforming to such Standards and Publications, nor shall the existence of
7、such Standards and Publications preclude their voluntary use by those other than TIA members, whether the standard is to be used either domestically or internationally. TIA Documents contain information deemed to be of technical value to the industry, and are published at the request of the originat
8、ing Committee without necessarily following the rigorous public review and resolution of comments which is a procedural part of the development of a American National Standard (ANS). Further details of the development process are available in the TIA Engineering Manual, located at http:/www.tiaonlin
9、e.org/standards/sfg/engineering_manual.cfm A Word from ATIS: ATIS is the leading technical planning and standards development organization committed to the rapid development of global, market-driven standards for the information, entertainment and communications industry. More than 200 companies act
10、ively formulate standards in ATIS Forums, covering issues including: IPTV, Cloud Services, Energy Efficiency, IP-Based and Wireless Technologies, Quality of Service, Billing and Operational Support, Emergency Services, Architectural Platforms and Emerging Networks. In addition, numerous Incubators,
11、Focus and Exploratory Groups address evolving industry priorities including Smart Grid, Machine-to-Machine, Networked Car, IP Downloadable Security, Policy Management and Network Optimization. ATIS is the North American Organizational Partner for the 3rd Generation Partnership Project (3GPP), a memb
12、er and major U.S. contributor to the International Telecommunication Union (ITU) Radio and Telecommunications Sectors, and a member of the Inter-American Telecommunication Commission (CITEL). ATIS is accredited by the American National Standards Institute (ANSI). For more information, please visit w
13、ww.atis.org. NOTICE FROM PATENT HOLDERS The users attention is called to the possibility that compliance with this standard may require use of an invention covered by patent rights. By publication of this standard, no position is taken with respect to the validity of this claim or of any patent righ
14、ts in connection therewith. The patent holder has, however, filed a statement of willingness to grant a license under these rights on reasonable and nondiscriminatory terms and conditions to applicants desiring to obtain a license. Details may be obtained from the Telecommunications Industry Associa
15、tion, Alliance for Telecommunications Industry Solutions or the American National Standards Institute. Copyright Telecommunications Industry Association 2012 Copyright Alliance for Telecommunications Industry Solutions 2012 All rights reserved This document is subject to change. NOTICE OF COPYRIGHT
16、This document is issued under a joint copyright by the Telecommunications Industry Association and the Alliance for Telecommunications Industry Solutions, and may not be reproduced without permission. Reproduction of these documents either in hard copy or soft copy (including posting on the web) is
17、prohibited without copyright permission. For copyright permission to reproduce portions of this document, please contact TIA Standards Department or go to the TIA website (www.tiaonline.org) for details on how to request permission. Details are located at: http:/www.tiaonline.org/about/faqDetail.cfm
18、?id=18 Organizations may obtain permission to reproduce a limited number of copies by entering into a license agreement. For information, contact: Global Engineering Documents 15 Inverness Way East Englewood, CO 80112-5704 or call U.S.A. and Canada (1-800-854-7179) International (303) 397-7956 OR AT
19、IS Document Center: http:/www.atis.org/docstore/default.aspx Alliance for Telecommunications Industry Solutions 1200 G Street, NW Suite 500 Washington, DC 20005 (202) 628-6380 NOTICE OF DISCLAIMER AND LIABILITY The document to which this Notice is affixed (the “Document”) has been prepared by one or
20、 more Engineering Committees or Formulating Groups of the Telecommunications Industry Association (“TIA”). In addition, the Document was balloted by ATIS Wireless Technologies and Systems Committee and ATIS Packet Technologies and Systems Committee. TIA is not the author of the Document contents, bu
21、t publishes and claims copyright to the Document pursuant to licenses and permission granted by the authors of the contents. TIA Engineering Committees and Formulating Groups are expected to conduct their affairs in accordance with the TIA Engineering Manual (“Manual”), the current and predecessor v
22、ersions of which are available at http:/www.tiaonline.org/standards/sfg/engineering_manual.cfm. The ATIS Wireless Technologies and Systems Committee and ATIS Packet Technologies and Systems Committee is expected to conduct its affairs in accordance with the ATIS Operating Procedures which is availab
23、le at http:/www.atis.org/legal/op.asp. . TIAs function is to administer the process, but not the content, of document preparation in accordance with the Manual and, when appropriate, the policies and procedures of the American National Standards Institute (“ANSI”). Likewise, ATIS function, and on be
24、half of its Committees and Forums, is to administer the process according to its Operating Procedures, but not develop the content of the document. TIA and ATIS do not evaluate, test, verify or investigate the information, accuracy, soundness, or credibility of the contents of the Document. In publi
25、shing the Document, TIA and ATIS disclaim any undertaking to perform any duty owed to or for anyone. If the Document is identified or marked as a project number (PN) document, or as a standards proposal (SP) document, persons or parties reading or in any way interested in the Document are cautioned
26、that: (a) the Document is a proposal; (b) there is no assurance that the Document will be approved by any Committee of TIA or any other body in its present or any other form; (c) the Document may be amended, modified or changed in the standards development or any editing process. The use or practice
27、 of contents of this Document may involve the use of intellectual property rights (“IPR”), including pending or issued patents, or copyrights, owned by one or more parties. Neither TIA nor ATIS makes any search or investigation for IPR. When IPR consisting of patents and published pending patent app
28、lications are claimed and called to TIAs attention, a statement from the holder thereof is requested, all in accordance with the Manual. When IPR consisting of patents are claimed and called to ATISs attention, a statement from the holder thereof is requested, all in accordance with the ATISs Operat
29、ing Procedures. Neither TIA nor ATIS takes any position with reference to, and disclaims any obligation to investigate or inquire into, the scope or validity of any claims of IPR. Neither TIA or ATIS will neither be a party to discussions of any licensing terms or conditions, which are instead left
30、to the parties involved, nor will TIA or ATIS opine or judge whether proposed licensing terms or conditions are reasonable or non-discriminatory. TIA does not warrant or represent that procedures or practices suggested or provided in the Manual have been complied with as respects the Document or its
31、 contents. TIA and ATIS do not enforce or monitor compliance with the contents of the Document. TIA and ATIS do not certify, inspect, test or otherwise investigate products, designs or services or any claims of compliance with the contents of the Document. ALL WARRANTIES, EXPRESS OR IMPLIED, ARE DIS
32、CLAIMED, INCLUDING WITHOUT LIMITATION, ANY AND ALL WARRANTIES CONCERNING THE ACCURACY OF THE CONTENTS, ITS FITNESS OR APPROPRIATENESS FOR A PARTICULAR PURPOSE OR USE, ITS MERCHANTABILITY AND ITS NON-INFRINGEMENT OF ANY THIRD PARTYS INTELLECTUAL PROPERTY RIGHTS. TIA AND ATIS EXPRESSLY DISCLAIM ANY AN
33、D ALL RESPONSIBILITIES FOR THE ACCURACY OF THE CONTENTS AND MAKE NO REPRESENTATIONS OR WARRANTIES REGARDING THE CONTENTS COMPLIANCE WITH ANY APPLICABLE STATUTE, RULE OR REGULATION, OR THE SAFETY OR HEALTH EFFECTS OF THE CONTENTS OR ANY PRODUCT OR SERVICE REFERRED TO IN THE DOCUMENT OR PRODUCED OR RE
34、NDERED TO COMPLY WITH THE CONTENTS. NEITHER TIA NOR ATIS SHALL BE LIABLE FOR ANY AND ALL DAMAGES, DIRECT OR INDIRECT, ARISING FROM OR RELATING TO ANY USE OF THE CONTENTS CONTAINED HEREIN, INCLUDING WITHOUT LIMITATION ANY AND ALL INDIRECT, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES (INCLUDING DAMAG
35、ES FOR LOSS OF BUSINESS, LOSS OF PROFITS, LITIGATION, OR THE LIKE), WHETHER BASED UPON BREACH OF CONTRACT, BREACH OF WARRANTY, TORT (INCLUDING NEGLIGENCE), PRODUCT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. THE FOREGOING NEGATION OF DAMAGES IS A FUNDAMENTAL ELEMENT O
36、F THE USE OF THE CONTENTS HEREOF, AND THESE CONTENTS WOULD NOT BE PUBLISHED BY TIA WITHOUT SUCH LIMITATIONS.ANSI/J-STD-025-B-1 Table of Contents 1. INTRODUCTION.1 2. SCOPE.1 3. SECTION REVISIONS1 Section 3 Definitions and Acronyms.1 Section 6.4.9 PartyIdentity.2 Annex I PartyIdentity.2 Index .2 iANS
37、I/J-STD-025-B-1 1. Introduction The purpose of this addendum is to add the necessary Mobile Equipment IDentifier (MEID) information to ANSI/J-STD-025-B. Paragraphs in ANSI/J-STD-025-B that are not shown remain the same. The section numbering in section 3 of this document aligns with the original sec
38、tions in ANSI/J-STD-025-B. 2. Scope This addendum only consists of additions to ANSI/J-STD-025-B adding MEID, as follows: a. Page 12 Line 46: Section 3 - Definitions and Acronyms Add Mobile Equipment IDentifier (MEID). b. Page 92 Line 10: Section 6.4.9 - PartyIdentity - Add meid. c. Page 220 Line 14
39、: Annex I - PartyIdentity - Add meid. d. Page 235 Lines 2 and 14: Index - Add meid and Mobile Equipment IDentifier e. Page 243 Line 43: Index - Add MEID 3. Section Revisions Text for ANSI/J-STD-025-B addendum adding MEID: Section 3 Definitions and Acronyms Mobile Equipment IDentifier (MEID): a 56-bi
40、t mobile equipment identifier used for new terminals as the alternative to the 32-bit ESN. Although ESNs have always been unique in the past, the introduction of the 56-bit MEID has led to creation of a 32-bit “pseudo-ESN” (pESN) for backward compatibility with legacy systems. A Pseudo-ESN (0x80 as
41、its Manufacturer Code, followed by the 24 least significant bits of the SHA-1 hash of the 56 bit MEID) is used when MEID isnt implemented in a system. The pESN is still the same for each particular mobile. If more than one mobile derive the same pESN from their MEIDs, then there is the potential for
42、 non-unique pESN representations and collisions. 1 ANSI/J-STD-025-B-1 Section 6.4.9 PartyIdentity; meid 21 VisibleString (SIZE (14) OPTIONAL, - Mobile Equipment IDentifier - a hexadecimal string e.g., “A0ABCDEFFFFFFF” Annex I - PartyIdentity; meid 21 VisibleString (SIZE (14) OPTIONAL, - Mobile Equipment IDentifier - a hexadecimal string e.g., “A0ABCDEFFFFFFF” Index - Mobile Equipment IDentifier; meid 92, 220 Mobile Equipment IDentifier 92, 220 MEID PartyIdentity 92, 220 2
