1、raising standards worldwideNO COPYING WITHOUT BSI PERMISSION EXCEPT AS PERMITTED BY COPYRIGHT LAWBSI Standards PublicationBS ISO 6751:2011Tools for moulding Ejectorpins with cylindrical headBS ISO 6751:2011 BRITISH STANDARDNational forewordThis British Standard is the UK implementation of ISO 6751:2
2、011. Itsupersedes BS ISO 6751:1998 which is withdrawn.The UK participation in its preparation was entrusted to TechnicalCommittee MTE/12, Tools for pressing and moulding.A list of organizations represented on this committee can beobtained on request to its secretary.This publication does not purport
3、 to include all the necessaryprovisions of a contract. Users are responsible for its correctapplication. BSI 2011ISBN 978 0 580 73919 4ICS 25.120.30Compliance with a British Standard cannot confer immunity fromlegal obligations.This British Standard was published under the authority of theStandards
4、Policy and Strategy Committee on 30 September 2011.Amendments issued since publicationDate Text affectedBS ISO 6751:2011Reference numberISO 6751:2011(E)ISO 2011INTERNATIONAL STANDARD ISO6751Fourth edition2011-09-15Tools for moulding Ejector pins with cylindrical head Outillage de moulage jecteurs tt
5、e cylindrique BS ISO 6751:2011ISO 6751:2011(E) COPYRIGHT PROTECTED DOCUMENT ISO 2011 All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm, without permiss
6、ion in writing from either ISO at the address below or ISOs member body in the country of the requester. ISO copyright office Case postale 56 CH-1211 Geneva 20 Tel. + 41 22 749 01 11 Fax + 41 22 749 09 47 E-mail copyrightiso.org Web www.iso.org Published in Switzerland ii ISO 2011 All rights reserve
7、dBS ISO 6751:2011ISO 6751:2011(E) ISO 2011 All rights reserved iiiForeword ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO member bodies). The work of preparing International Standards is normally carried out through ISO technical
8、committees. Each member body interested in a subject for which a technical committee has been established has the right to be represented on that committee. International organizations, governmental and non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with
9、the International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization. International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2. The main task of technical committees is to prepare International Standards. Draft Interna
10、tional Standards adopted by the technical committees are circulated to the member bodies for voting. Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote. Attention is drawn to the possibility that some of the elements of this document may b
11、e the subject of patent rights. ISO shall not be held responsible for identifying any or all such patent rights. ISO 6751 was prepared by Technical Committee ISO/TC 29, Small tools, Subcommittee SC 8, Tools for pressing and moulding. This fourth edition cancels and replaces the third edition (ISO 67
12、51:1998), of which it constitutes a minor revision. In particular, the indication of surface textures has been updated in accordance with ISO 1302:2002. BS ISO 6751:2011BS ISO 6751:2011INTERNATIONAL STANDARD ISO 6751:2011(E) ISO 2011 All rights reserved 1Tools for moulding Ejector pins with cylindri
13、cal head 1 Scope This International Standard specifies the dimensions and tolerances, in millimetres, of ejector pins with cylindrical head which are used in compression and injection moulds and in die casting dies. It also gives material guidelines and hardness requirements, and specifies the desig
14、nation of ejector pins with cylindrical head. Flat ejector pins are specified in ISO 8693 and shouldered ejector pins are specified in ISO 8694. 2 Dimensions The dimensions of ejector pins shall be in accordance with the indications of Figure 1 and Tables 1 and 2. Surface roughness values in microme
15、tres Key 1 edge without burrs aRa 0,8 for hot worked steel. Ra 0,4 for alloyed cold worked steel. bProviding the ejector pin with an alternative surface roughness or a small variation on the diameter, D1, over a certain length is permitted. Figure 1 Ejector pin with cylindrical head BS ISO 6751:2011
16、ISO 6751:2011(E) 2 ISO 2011 All rights reservedTable 1 Dimensions of ejector pins with cylindrical head of hot worked steel Dimensions in millimetres D1g6 D2L20HR Standardsize Oversize 00,2100 125 160 200 250 315 400 500 630 800 1 000 00,050,202 4 X X X X 2 0,2 2,2 X X 2,5 5 X X X X 0,3 2,7 X X 3 6
17、X X X X X X 3 3,2 X X X 3,5 7 X X X X X X 3,7 X X X 4 8 X X X X X X X 4,2 X X X X 5 10 X X X X X X X X 5,2 X X X X 6 12 X X X X X X X X X 5 0,5 6,2 X X X X X 8 14 X X X X X X X X X X 8,2 X X X X X 10 16 X X X X X X X X X X X 10,2 X X X X X X 12 18 X X X X X X X X X X 70,8 12,5 X X X X X X X X X X 16
18、 22 X X X X X X X X X 20 26 X X X X X X X X X 8 1 25 32 X X X X X X X X 10 32 40 X X X X X X X BS ISO 6751:2011ISO 6751:2011(E) ISO 2011 All rights reserved 3Table 2 Dimensions of ejector pins with cylindrical head of alloyed cold worked steel Dimensions in millimetres D1g6D2L20HR Standardsize Overs
19、ize 00,280 100 125 160 200 250 315 400 00,050,201,5 3 X X X X 1,5 0,2 1,6 X X X X 2 4 X X X X X 2 2,2 X X X 2,5 5 X X X X X 0,3 2,7 X X X 3 6 X X X X X X 3 3,2 X X X 3,5 7 X X X X X X 3,7 X X X 4 8 X X X X X X X 4,2 X X X X 5 10 X X X X X X X 5,2 X X X X 6 12 X X X X X X X 5 0,5 6,2 X X X X 8 14 X X
20、 X X X X X X 8,2 X X X X 10 16 X X X X X X X 10,2 X X X X 12 18 X X X X X X X 70,8 12,5 X X X X X X X 16 22 X X X X X X X 20 26 X X X X X X 8 1 3 Material and hardness Ejector pins with cylindrical head shall be made of hot worked steel or alloyed cold worked steel. The hardness of the shaft and hea
21、d shall conform to the indications of Table 3. BS ISO 6751:2011ISO 6751:2011(E) 4 ISO 2011 All rights reservedTable 3 Material and hardness Material HardnessaShaft Head Hot worked steel Min. 1 400 MPa core strength min. 950 HV 0,3 (45 5) HRC hot-forged Alloyed cold worked steel (60 2) HRC aThe point
22、 at which hardness is measured is left to the manufacturers discretion. 4 Designation Ejector pins with cylindrical head according to this International Standard shall be designated by: a) “ejector pin with cylindrical head”; b) reference to this International Standard, i.e. ISO 6751; c) ejector pin
23、 diameter, D1, in millimetres; d) ejector pin length, L, in millimetres; e) ejector pin material. EXAMPLE The designation for an ejector pin with cylindrical head of diameter D1= 2 mm, of length L = 100 mm and of hot worked steel is as follows: Ejector pin with cylindrical head ISO 6751 - 2 - 100 -
24、Hot worked steel BS ISO 6751:2011ISO 6751:2011(E) ISO 2011 All rights reserved 5Bibliography 1 ISO 1302:2002, Geometrical Product Specifications (GPS) Indication of surface texture in technical product documentation 2 ISO 8693, Tools for moulding Flat ejector pins 3 ISO 8694, Tools for moulding Shou
25、ldered ejector pins BS ISO 6751:2011ISO 6751:2011(E) ICS 25.120.30 Price based on 5 pages ISO 2011 All rights reserved This page deliberately left blankBSI is the independent national body responsible for preparing British Standardsand other standards-related publications, information and services.
26、It presents the UK view on standards in Europe and at the international level. It is incorporated by Royal Charter.British Standards Institution (BSI)raising standards worldwideBSI Group Headquarters389 Chiswick High Road London W4 4AL UKTel +44 (0)20 8996 9001Fax +44 (0)20 8996 Standards are updat
27、ed by amendment or revision. Users of British Stan-dards should make sure that they possess the latest amendments or editions.It is the constant aim of BSI to improve the quality of our products and serv-ices. We would be grateful if anyone finding an inaccuracy or ambiguity whileusing this British
28、Standard would inform the Secretary of the technical com-mittee responsible, the identity of which can be found on the inside frontcover.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001BSI offers Members an individual updating service called PLUS which ensuresthat subscribers automatically receive
29、the latest editions of standards.Tel: +44 (0)20 8996 7669 Fax: +44 (0)20 8996 7001Email: Buying standardsYou may buy PDF and hard copy versions of standards directly using acredit card from the BSI Shop on the website addition all orders for BSI, international and foreign standards publicationscan
30、be addressed to BSI Customer Services.Tel: +44 (0)20 8996 9001 Fax: +44 (0)20 8996 7001Email: In response to orders for international standards, it is BSI policy tosupply the BSI implementation of those that have been publishedas British Standards, unless otherwise requested.Information on standards
31、BSI provides a wide range of information on national, Europeanand international standards through its Knowledge Centre.Tel: +44 (0)20 8996 7004 Fax: +44 (0)20 8996 7005Email: Various BSI electronic information services are also available whichgive details on all its products and services. Tel: +44 (
32、0)20 8996 7111 Fax: +44 (0)20 8996 7048Email: BSI Subscribing Members are kept up to date with standardsdevelopments and receive substantial discounts on the purchase priceof standards. For details of these and other benefits contact Membership Ad-ministration. Tel: +44 (0)20 8996 7002 Fax: +44 (0)2
33、0 8996 7001 Email: Information regarding online access to British Standards via BritishStandards Online can be found at information about BSI is available on the BSI website at www.bsi- subsists in all BSI publications. BSI also holds the copyright,in the UK, of the publications of the internation
34、al standardization bodies. Ex-cept as permitted under the Copyright, Designs and Patents Act 1988 no ex-tract may be reproduced, stored in a retrieval system or transmitted in anyform or by any means electronic, photocopying, recording or otherwise without prior written permission from BSI. This doe
35、s not preclude the freeuse, in the course of implementing the standard of necessary details such assymbols, and size, type or grade designations. If these details are to be usedfor any other purpose than implementation then the prior written permissionof BSI must be obtained. Details and advice can be obtained from the Copy-right & Licensing Manager.Tel: +44 (0)20 8996 7070Email:
