1、 DETAIL SPECIFICATION SHEET CONNECTORS, ELECTRICAL, RECEPTACLE, PIN CONTACT, MINIATURE, RECTANGULAR TYPE, RACK TO PANEL, STAGGERED STANDARD HOLE MOUNTING, ENVIRONMENT RESISTING, 200C This specification is approved for use by all Departments and Agencies of the Department of Defense. The requirements
2、 for acquiring the product described herein shall consist of this specification sheet and MIL-DTL-83733. FIGURE 1. Dimensions and configurations. . INCH-POUND MIL-DTL-83733/9C 31 January 2011 SUPERSEDING MIL-C-83733/9B (USAF) 10 December 1980 .286 .276 (2 HOLES) DIA .223 .213 (4 PLACES) DIA L M .566
3、 .558 1.170 1.146 SEE NOTE 3 N Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83733/9C 2 Shell size L M N A 3.030 3.000 2.580 2.570 2.150 2.130 B 4.330 4.300 3.880 3.870 3.450 3.430 Inches mm Inches mm Inches mm .213 5.41 1.170 29.72 3.030 7
4、6.96 .223 5.66 2.130 54.10 3.870 98.30 .286 7.26 2,150 54.61 3.880 98.55 .558 14.17 2.570 65.28 4.300 109.22 .566 14.38 2.580 65.53 4.330 109.98 1.146 29.11 3.000 76.20 NOTES: 1. Dimensions are in inches. 2. See MIL-DTL-83733 for interface and backend configuration requirements. 3. This receptacle m
5、ates with MIL-DTL-83733/12 plug. 4. For contacts see MIL-DTL-83733 and SAE AS39029/4, SAE AS39029/50 or SAE AS39029/58. 5. For insert arrangements see MIL-STD-1531 and MIL-STD-1532. 6. Layout arrangements containing size 22D contacts shall not be used in this shell configuration. 7. Metric equivalen
6、ts are given for information only and are based upon 1.00 inch equals 25.4 mm. FIGURE 1. Dimensions and configurations - Continued. Changes from previous issue. The margins of this specification are marked with vertical lines to indicate where changes from the previous issue were made. This was done
7、 as a convenience only and the Government assumes no liability whatsoever for any inaccuracies in these notations. Bidders and contractors are cautioned to evaluate the requirements of this document based on the entire content irrespective of marginal notations and relationship to the last previous
8、issue. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-DTL-83733/9C 3 Referenced documents. In addition to MIL-DTL-83733, this document references the following: MIL-DTL-83733/12 MIL-STD-1531 MIL-STD-1532 SAE AS39029/4 SAE AS39029/50 SAE AS39029/
9、58 CONCLUDING MATERIAL Custodians: Preparing activity: Air Force - 85 DLA CC DLA - CC (Project 5935-2010-037) Review activity: Air Force 99 NOTE: The activities listed above were interested in this document as of the date of this document. Since organizations and responsibilities can change, you should verify the currency of the information above using the ASSIST Online database at https:/assist.daps.dla.mil/ Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-
