1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Changed the dose rate from 3 rads(Si)/s to 1 rads(Si)/s in section 1.5 for Maximum total dose available condition. Boilerplate paragraphs updated. ksr 04-11-08 Raymond Monnin B Section 1.3, changed supply voltage range high end (VDD1) to 2.1V. Ad
2、ded new footnote 4/ in section 1.4 and renumbered footnotes in section 1.5. Made significant change to max value in Table I for Operating supply current IDD1and Supply current standby IDD1. Added new footnote 1/ to Table I renumbered other footnotes and added footnote 7/ to Supply current standby sy
3、mbol blocks in Table I. Corrected the outline letter in Figure 2 from X to U. ksr 09-05-05 Joseph Rodenbeck REV SHEET REV B B B B B B B B B B B SHEET 15 16 17 18 19 20 21 22 23 24 25 REV STATUS REV B B B B B B B B B B B B B B OF SHEETS SHEET 1 2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Kenn
4、eth Rice DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 http:/www.dscc.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Raj Pithadia THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Raymond Monnin MICROCIRCUIT, MEMORY, DIGITAL, CMOS, 512K x 8-BIT (4M), RADIATION-HARDENED SR
5、AM, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 03 11 18 AMSC N/A REVISION LEVEL B SIZE A CAGE CODE 672685962-03235 SHEET 1 OF 25 DSCC FORM 2233 APR 97 5962-E224-09 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-
6、,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03235 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing documents three product assurance class levels consisting of high reliability (device classes Q and M), space app
7、lication (device class V), and for appropriate satellite and similar applications (device class T). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness Assurance (RHA) levels are reflected
8、 in the PIN. For device class T, the user is encouraged to review the manufacturers Quality Management (QM) plan as part of their evaluation of these parts and their acceptability in the intended application. 1.2 PIN. The PIN shall be as shown in the following example: 5962 R 03235 01 Q U C Federal
9、RHA Device Device Case Lead stock class designator type class outline finish designator (see 1.2.1) (see 1.2.2) designator (see 1.2.4) (see 1.2.5) / (see 1.2.3) / Drawing number 1.2.1 RHA designator. Device classes Q, T and V RHA marked devices shall meet the MIL-PRF-38535 specified RHA levels and a
10、re marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535 appendix A specified RHA levels and shall be marked with the appropriate RHA designator. A dash (-) indicates a non-RHA device. 1.2.2 Device types. The device types shall identify the circuit func
11、tion as follows: Device type Generic number 1/ Circuit function Access time 01 8R512K8 512K X 8-bit Radiation-hardened SRAM (MIL Temp) 15 ns 02 8R512K8 512K X 8-bit Radiation-hardened SRAM (Extended Temp) 15 ns 1.2.3 Device class designator. The device class designator shall be a single letter ident
12、ifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535, appendix A Q, V Certification and qualification to MIL-PRF-38
13、535 T Certification and qualification to MIL-PRF-38535 with performance as specified in the device manufacturers approved quality management plan 1.2.4 Case outline(s). The case outline(s) shall be as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package
14、style U See figure 1 36 Bottom braze Flat-pack 1.2.5 Lead finish. The lead finish shall be as specified in MIL-PRF-38535 for classes Q, T and V or MIL-PRF-38535, appendix A for device class M. _ 1/ Generic numbers are also listed on the Standard Microcircuit Drawing Source Approval Bulletin at the e
15、nd of this document and will also be listed in QML-38535 and MIL-HDBK-103. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03235 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET
16、 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 2/ 3/ Supply voltage range, (VDD1) -0.3 V dc to +2.1 V dc Supply voltage range, (VDD2) -0.3 V dc to +3.8 V dc Voltage range on any input pin -0.3 V dc to +3.8 V dc Voltage range on any output pin -0.3 V dc to +3.8 V dc Input current, dc . + 5 mA
17、 Power dissipation . 1.2 W Operating case temperature range, (TC) (Device 01) . -55C to +125C Operating case temperature range, (TC) (Device 02) . -40C to +125C Storage temperature range, (TSTG) -65C to +150C Junction temperature, (TJ) . +150C Thermal resistance, junction-to-case, (JC): Case U . +5C
18、/W 1.4 Recommended operating conditions. Supply voltage range, (VDD1) +1.7 V dc to +1.9 V dc 4/ Supply voltage range, (VDD2) 3.0 V dc to +3.6 V dc Supply voltage, (VSS) . 0 V dc Input voltage, dc. 0 V dc to VDD2Operating case temperature, (TC) (Device 01) . -55C to +125C Operating case temperature,
19、(TC) (Device 02) . -40C to +125C 1.5 Radiation features Maximum total dose available (dose rate = 1 rads(Si)/s) . 30.0x 104rads(Si) Dose rate upset . 5/ Dose rate survivability . 5/ Single event phenomenon (SEP) effective linear energy threshold (LET) with no upsets 5/ with no latch-up . 100 MeV-cm2
20、/mg 5/ Neutron irradiation . 3.0E14 n/cm22. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of these documents are tho
21、se listed in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Electronic Component Case
22、Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings (SMDs). MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at http:/assist.daps.dla.mil/quicksearch/ or from the Standardization Document Order Desk, 700 Robbin
23、s Avenue, Building 4D, Philadelphia, PA 19111-5094.) _ 2/ Stresses above the absolute maximum rating may cause permanent damage to the device. Extended operation at the maximum levels may degrade performance and affect reliability. 3/ All voltage values in this drawing are with respect to VSS. 4/ Fo
24、r increased noise immunity, supply voltage (VDD1) can be increased to 2.0 V. The parameters in Table I, (Electrical performance characteristics) are guaranteed through characterization at VDD1= 2.0 V dc. 5/ Contact the device manufacturer for detailed lot information. Provided by IHSNot for ResaleNo
25、 reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03235 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 4 DSCC FORM 2234 APR 97 2.2 Non-Government publications. The following document(s) form a part of this do
26、cument to the extent specified herein. Unless otherwise specified, the issues of the documents are the issues of the documents cited in the solicitation. AMERICAN SOCIETY FOR TESTING AND MATERIALS (ASTM) ASTM Standard F1192-00 - Standard Guide for the Measurement of Single Event Phenomena (SEP) Indu
27、ced by Heavy Ion Irradiation of Semiconductor Devices. (Applications for copies of ASTM publications should be addressed to: ASTM International, PO Box C700, 100 Barr Harbor Drive, West Conshohocken, PA 19428-2959; http:/www.astm.org.) ELECTRONICS INDUSTRIES ASSOCIATION (EIA) JEDEC Standard EIA/JESD
28、78 - IC Latch-Up Test. (Applications for copies should be addressed to the Electronics Industries Association, 2500 Wilson Boulevard, Arlington, VA 22201; http:/www.jedec.org.) (Non-Government standards and other publications are normally available from the organizations that prepare or distribute t
29、he documents. These documents also may be available in or through libraries or other informational services.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, how
30、ever, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q, T and V shall be in accordance with MIL-PRF-38535, and as specified herein or as modified in the device manufa
31、cturers Quality Management (QM) plan. The modification in the QM plan shall not effect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A and as specified herein. 3.2 Design, construction, and phys
32、ical dimensions. The design, construction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q, T and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outline(s). The case outline(s) shall be in accordance with 1.2.4 and figure 1 her
33、ein. 3.2.2 Terminal connections. The terminal connections shall be as specified on figure 2. 3.2.3 Truth table(s). The truth table(s) shall be as specified on figure 3. 3.2.4 Data retention and Output load circuit. The output load circuit shall be as specified on figure 4. 3.2.5 Timing waveforms. Th
34、e timing waveforms shall be as specified on figure 5. 3.2.6 Radiation test circuit. The radiation test circuit shall be as specified on figure 6. 3.2.7 Functional tests. Various functional tests used to test this device are contained in appendix A. If the test patterns cannot be implemented due to t
35、est equipment limitations, alternate test patterns to accomplish the same results shall be allowed. For device class M, alternate test patterns shall be maintained under document revision level control by the manufacturer and shall be made available to the preparing or acquiring activity upon reques
36、t. For device classes Q, T and V, alternate test patterns shall be under the control of the device manufacturers Technology Review Board (TRB) in accordance with MIL-PRF-38535 and shall be made available to the preparing or acquiring activity upon request. 3.3 Electrical performance characteristics
37、and post-irradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and post-irradiation parameter limits are as specified in table I and shall apply over the full ambient operating temperature range. Provided by IHSNot for ResaleNo reproduction or ne
38、tworking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-03235 DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43218-3990 REVISION LEVEL B SHEET 5 DSCC FORM 2234 APR 97 3.4 Electrical test requirements. The electrical test requirements shall be the subgroups specified
39、in table IIA. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For packages where marking of the entire SMD PIN number is not feasible due to space limitation
40、s, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q, T, and V shall be in accordance with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-3
41、8535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q, T and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device
42、classes Q, T and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of compliance shall be required from a manufacturer in order to be listed as an approved
43、 source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DSCC-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturers product meets, for device classes Q, T and V, the requirements of MIL-PRF-38535 and herein or
44、 for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q, T and V in MIL-PRF-38535 or for device class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits d
45、elivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DSCC-VA of change of product (see 6.2 herein) involving devices acquired to this drawing is required for any change that affects this drawing. 3.9 Verification and review for device class M.
46、For device class M, DSCC, DSCCs agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation. Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M.
47、 Device class M devices covered by this drawing shall be in microcircuit group number 41 (see MIL-PRF-38535, appendix A). 4. VERIFICATION 4.1 Sampling and inspection. For device classes Q and V, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 or as modified in the device
48、 manufacturers Quality Management (QM) plan including screening (4.2), qualification (4.3), and conformance inspection (4.4). The modification in the QM plan shall not affect the form, fit, or function as described herein. For device class T, sampling and inspection procedures shall be in accordance with MIL-PRF-38535 and the device manufacturers QM plan, including screening, qualification, and conformance inspection. The performance envelope and reliability information shall be as specified in the manufactur
