1、L !INCH-POUNDI MIL-B-82572A 31 May 1 989 SUPERSEDING MIL-B-82572 28 February 1969 MILITARY SPECIFICATION BOMB, GENERAL PURPOSE, MARK 84, 2000 POUND, EXPLOSIVE LOADING, ASSEMBLING, AND PACKING This specification is approved for use by al.1 Departments and Agencies of the Department of Defense. 1. SCO
2、PE l. 1 Scope, This specification establishes special requirements normal ly not required by the appl i cab1 e drawings and provi des qual i ty assurance provisions for the explosive loading, assembly, and packaging of the general purpose bomb designated as Bomb, GP, MK 84, 2000 Pound. 2. APPLICABLE
3、 DOCUMENTS 2.1 Government documents. 2.1 . 1 SGeci fi cations . standards. and handbooks. The fol 1 owi ng specifications, standards, and handbooks form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those listed in the issue of
4、the Department of Defense Index of Specifications and Standards (DODISS) and supplement thereto, cited in the solicitation (see 6.2). SPEC1 FICATIONS MI LITARY DOD-D-1000 MIL-E-22267 MIL-1-45607 Drawings, Engineering and Associated Li sts Explosive Compositions, HBX Type Inspection Equipment, Supply
5、 and Maintenance of Beneficial comments (recommendations, additions, deletions) and any pertinent data which may be of use in improving thi S document should be addressed to: Naval Air Engineering Center, Systems Engineering and Standardization Department (Code 531, Lakehurst, NJ 08733-5100, by usin
6、g the self-addressed Standardization Document Improvement Proposal (DD Form 1426) appearincr at the end of thi S document or by 1 etter. I AMSC NIA FSC 1325 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARDS MILITARY MI L-STD-105 Sampling Proc
7、edures and Tables for Inspection by Attributes MIL-STD-129 Marking for Shipment and Storage MIL-STD-746 Radiographic Testing Requirements for Cast Explosives MI L-STD- 1 1 67 Ammuni tion Data Card MI L-STD-1168 Lot Numbering of Ammuni tion MIL-STD-1320-53 Truckload ng Bomb, General Purpose, MK 84 an
8、d Mods (2000 LB) (With Plastic Nose Plug) in Adapter, Unit Load, MK 79 MOD O Fleet Issue Unit Load MIL-STD-1325-85 Railcar Loading of Hazardous Materials Bomb, General Purpose, MK 84 MODS O, 1, and 2 (2000 LB) in Unit Load Adapter MK 79 MOD O MIL-STD-45662 Cali bration System Requirements (Un1 ess o
9、therwi se i ndi cated, Copi es of federal and mi 1 i tary speci fi cations, standards, and handbooks are available from the Naval Pub1 ications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19111-5096.) 2.1.2 Other Government documents, drawings. and publications. The followin
10、g other Government documents, drawings, and publications form a. part of this document to the extent specified herein. Unless otherwise specified, the issues are those cited in the sol ici tation. OTHER GOVERNMENT DOCUMENTS DEPARTMENT OF DEFENSE (DOD) DOD 41 45.26M DOD Contractors Safety Manual for
11、Ammunition Explosives and Related Dangerous Material (Un1 ess otherwise indicated, Copi es of DOD 4145.26M are avai lab1 e from the Naval Publications and Forms Center, (ATTN: NPODS), 5801 Tabor Avenue, Philadelphia, PA 19111-5096.) DRAW I NGS NAVAL AIR SYSTEMS COMMAND (NAVAIR) 138091 1 Bomb, MK 84
12、MODS, G.P. 2000 Lb Loading Assembly 4902049 923AS104 Bomb, MK 84 MOD 3, General Purpose (GP) 2000 Pound, Thermally Protected, Loading Assembly Bomb, MK 84 MOD 4, GP 2000 Pound Loading Assembly 2 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-8
13、2572A 33 m 997990b 0362305 9 W t MIL-B-82512A DRAWINGS - Continued . NAVAL AIR SYSTEMS COMMAND (NAVAIR) 923AS107 Bomb, MK 84 MOD 5, GP 2000 Pound, Thermal ly Protected, Loading Assembly 923AS519 Bomb, MK 84 MOD 6, GP 2000 Pound, Thermally Protected, Loading Assembly 923AS527 Bomb, MK 84 MOD 7, GP 20
14、00 Pound Loading Assembly DL 138091 1 . . Bomb, MK 84 MOD 2, Li st of Drawings and Speci fi cations DL 2642646 Unit Load Adapter, MK 79 MOD O DL 4902049 DL 923AS104 DL 923AS107 DL 923AS519 DL 923AS527 Bomb, MK 84 MOD 3, List of Drawings and Specifications Bomb, MK 84 MOD 4, Li st of Drawings and Spe
15、ci fi cations Bomb, MK 84 MOD 5, Li st of Drawings and Specifications Bomb, MK 84 MOD 6, List of Drawings and Specifications Bomb, MK 84 MOD 7, Li st of Drawi ngs and Speci fi cations (Unless otherwise indicated, copies of NAVAIR drawings are available from the Naval Air Technical Services Faci 1 i
16、ty (NATSF) (Code 3121 1, 700 Robbins Avenue, Philadelphia, PA 19111-5096.) PUBLICATIONS NAVAL SEA SYSTEMS COMMAND (NAVAL WEAPONS STATION EARLE ENGINEERING DEPT) WR 51/42 WR 52/73 WR 541127 Weapons Requirement , Truckloadi ng 2000 Lb L. D. Bomb MK 84 and MODS, Loose with Plastic Nose Plugs Weapons Re
17、quirement Carloading 2000 Lb L.D. Bomb MK 84 and MODS, Loose With Plastic Nose Plugs Weapons Requirement, Pal lefizing F1 eet Issue Unit Load, 2000 Lb Low Drag Bomb (G.P.) MK 84 and MODS with Metal or Plastic Nose Plugs in Unit Load Adapter MK 79 MOD O (Un1 ess otherwi se i ndi cated, Copi es of Wea
18、pons Requi rements are- avai .1 ab1 e from the Naval Ordnance Station (Code 802) Louisville, KY 40214-5001.) 3 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-l MIL-B-82572A 2.2 Order of precedence. In the event of a conflict between the text of this
19、 document and the references cited herein, the text of this document takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a specific exemption has been obtained. 3, REQUIREMENTS 3.1 First article. When specified (see 6.2), a sample shall be subjected
20、 to first article inspection (see 6.4) in accordance with 4.4. 3.2 Desian and construction. The design and construction of the bomb shall be in accordance with the requirements specified herein and with the applicable drawings and documents for the bomb being procured (see 3.3). 3.3 Explosive 1-oadi
21、ng. Explosive loading shall be in accordance with the applicable loading drawings as follows: 1380911, MK 84 MOD 2, listed on DL 138091 1 , 4902049, MK 84 MOD 3 1 i sted on DL 4902049, 923AS104, MK 84 MOD 4, listed on DL 923AS104, 923AS107, MK 84 MOD 5, listed on DL 923AS107, 923AS519, MK 84 MOD 6,
22、DL 923AS519, and 923AS527, MK 84 MOD 7 , 1 i sted on DL 923AS527. 3.4 Explosive composition, The explosive composition used in loading the assembly shall be tritonal 80/20 or H-6 explosive composition as specified by the acquiring activity (see 6.2). 3.4.1 Tri tonal (80/20) explosive composition, Tr
23、itonal (80/20) explosive composition shall consist of 80% f. 3% trinitrotoluene (TNT) and 20% 3% aluminum (see 4.6.2). 3.4.2 H-6 explosive composition. H-6 explosive composition shall conform to the requirements of MIL-E-22267 (see 4.6.2). . asphal tic compound on the interior surfaces of the bomb a
24、ssembly shall be in accordance with the applicable loading drawing (see 3.3) when tested as specified in 4.5 and 4.6.3. 3.5 Weiaht of applied asphaltic compound. The total weight of the 3.6 Radioaraphic examination of the explosive charae. The loaded bomb shall be subjected to radiographic examinati
25、on in accordance with 4.5 and 4.6.4 to ensure that: a. No shrinkage cavity larger than 10 square inches in cross section area is located less than 6 inches from the nose fuze 1 i ner. b. No shrinkage cavity contacts more than one half of the surface c. No shrinkage cavity is located less than 1.5 in
26、ches from the area of the forward 3 inches of the base fuze liner. suspension 1 ug area. 3.7 Safety. The contractor shall observe the safety precautions of DOD 41 45.26M as appl i cab1 e. 4 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MI L-B-82572
27、A 3.8 Markinq. Each bomb shall be marked as specified on the applicable loading drawing (see 3.3). 3.9 Horkmanship. All interior bomb surfaces requiring application of asphal tic compound shall be free of chips,. dirt, oi 1, grease, rust, and other materi al before applying asphal ti c compound and,
28、 before loading of explosive charge. Outer bomb skin and other surfaces shall be free of chips, dirt, rust, or other imperfections. All interior surfaces of the bomb assembly shall be completely coated and shall be protected from contamination, The cleaning method used to remove explosive material f
29、rom the exterior surfaces of the bomb, fuze cavities, charging tubes, and threads shall not be injurious to any of the parts nor shall the parts be contaminated by the cleaning method. 4. QUALITY ASSURANCE PROVISIONS 4.1 Responsi bi li tv for insDection. Unless otherwise specified in the contract or
30、 purchase order, the contractor is responsible for the performance of al 1 inspection requirements (examinations and tests) as specified herein. Except as otherwise specified in the contract or purchase order, the contractor may use his own or any other faci 1 i ties sui table for the performance of
31、 the inspection requirements speci fi ed herei n, un1 ess disapproved by the Government. The Government reserves the right to perform any of the inspections set forth in this specification where such inspections are deemed necessary to ensure supplies and services conform to prescribed requirements.
32、 4.1.1 Responsibilitv for compliance All items shall meet all requirements of sections 3 and 5, The inspection set forth in this specification shall become a part of the contractors overall inspection system or quality program. The absence of any inspection requirements in the specification shall no
33、t re1 ieve the contractor of the responsi bi 1 i ty of ensuring that all products or supplies submitted to the Government for acceptance comply with al 1 requirements of the contract. Sampling inspection, as part of manufacturing operations, is an acceptable practice to ascertain conformance to requ
34、irements, however, this does not authorize submission of known defective material, either indicated or actual, nor does it commit the Government to accept defective material. 4.2 Classification of insDections. The inspect herein are classified as fol lows: ion requirements specified a. First article
35、 inspection (see 4.4). b. Quality conformance inspection (see 4.5). 4.3 Inspection equipment. The inspection equipment required to perform the examinations and tests prescribed in this specification shall be in accordance with inspection equipment which has been reviewed or provided by an approved G
36、overnment test faci 1 i ty. 4.3.1 Inspection equirment data, Inspection equipment lists and detailed drawings for contractor designed inspection equipment shall be prepared and be available to the acquiring activity as specified in the contract or purchase order (see 4.3.2, 6.2, and 6.3). Provided b
37、y IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-MIL-B-82572A 33 777770b 0362308 4 -1 MIL-B-82572A 4.3.2 Contractor desiuned inspection equipment. When specified by the acquiring activity, contractor designed inspection equipment shall be in accordance with 4.3
38、.2.1 through 4.3.2.5. 4.3.2.1 Inspection equipment lists. Inspection equipment lists shall be prepared by the contractor in accordance with DOD-D-1000 (see 6.31, indicating the avai labi 1 i ty of inspection equipment designs, the numbers of drawings, or Federal Stock Numbers of existing equipment d
39、esigns, or codes as indicated in 4.3.2.2. Design action required of the contractor is described in 4.3.2.3 and 4.3.2.4. The contractor wi 11 be required to prepare detai 1 ed drawings in accordance with 4.3.2.4 for all the equipment coded as Yontractor Design.“ These contractor designs shall be appr
40、oved by the Government prior to fabrication or procuring of the equipment. Designs shall be avai lab1 e for approval as specified in 4.3.2.5. 4.3.2.2 Inspection equipment list codes. The inspection equipment as defined in 4.3.2.3 and 4.3.2.4 will be designated by the following codes: CD - Contractor
41、 design on .controlled contractor format or commercial equi.pment. DOD - Mi 1 i tary design, mandatory for use. 4.3.2.3 Militarv designs. Military designs are reflected on detailed drawings which completely depict al 1 the information necessary for the fabrication of the item of inspection equipment
42、. The contractor need provide no design when a mi 1 i tary design is 1 i sted for an i tem of inspection equipment. Military designs fall into two basic classifications: mandatory (designated llDOD1l) and non-mandatory (indicated by drawing or Federal Stock Number). When an inspection equipment list
43、 references mandatory mi li tary designs, the contractor shall comply with and use these designs accordingly. The contractor may, however, in connection with non-mandatory designs and with the approval of the Government, design al ternate inspection equipment or use comparable commercial equipment t
44、o faci 1 i tate hi S operations. Such contractor prepared designs or commercial equipment selections shall be approved by the Government prior to fabrication or procuring of the equipment. Designs shall be available for approv.al as specified in 4.3.2.5. 4.3.2.4 Contractor desiuns. Contractor design
45、s are designs of inspection equipment for which the Government has assigned design responsibility to the contractor. Contractor designs shall be supported by detai 1 ed drawings which depict al 1 the information. necessary to completely fabricate, cal i brate, and operate an i tem of inspection equi
46、pment. This requires that the necessary views, dimensions, materials, finish, notes, operating, and calibration instructions be properly depicted in accordance with approved practices to the extent that further calculation or clarification will not be required. Unless otherwise specified, contractor
47、 designs may be developed on the format the contractor normally employs in his equipment design procedures provided such format reflects the detail and information specified above, subject to the following controls: All available contractor designs shall conform to DOD-D-1000 (see 6.3). Legibility a
48、nd reproduci bi 1 i ty shall permit conventional making of clearly understandable, high contrast reproductions. The contractor shall make available one copy of final designs as a rol led set. Designs shall be available for approval as specified in.4.3.2.5. 6 Provided by IHSNot for ResaleNo reproduct
49、ion or networking permitted without license from IHS-,-,-MIL-B-82572A L3 E 777770b 03b2L07 b M MIL-B-82572A 4.3.2.5 Availability of contractor designs. Unless otherwise specified by this specification, all designs of equipment for inspection OP defects classified as critical and major shall be available for approval to the departmental agency as designated by the contracting offi Cer. Al 1 other designs of inspection equipment shall be approved by the Governm
