1、 REVISIONS LTR DESCRIPTION DATE (YR-MO-DA) APPROVED A Add RHA data and limits. Editorial changes throughout. - jak 99-03-10 Monica L. Poelking B Update the boilerplate to current requirements as specified in MIL-PRF-38535. Editorial changes throughout. jak 07-03-15 Thomas M. Hess C Updated DC output
2、 current (ICC, IGND) in section 1.3, add source of supply information cage 0C7V7. Update the boilerplate paragraphs to current requirements as specified in MIL-PRF-38535. jwc 13-03-22 Thomas M. Hess REV SHEET REV C C C C SHEET 15 16 17 18 REV STATUS REV C C C C C C C C C C C C C C OF SHEETS SHEET 1
3、2 3 4 5 6 7 8 9 10 11 12 13 14 PMIC N/A PREPARED BY Wanda L. Meadows DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 http:/www.landandmaritime.dla.mil STANDARD MICROCIRCUIT DRAWING CHECKED BY Thomas J. Ricciuti THIS DRAWING IS AVAILABLE FOR USE BY ALL DEPARTMENTS APPROVED BY Monica L. Poelking MICRO
4、CIRCUIT, DIGITAL, ADVANCED CMOS, OCTAL BUFFER/LINE DRIVER WITH NONINVERTING THREE-STATE OUTPUTS, TTL COMPATIBLE INPUTS, MONOLITHIC SILICON AND AGENCIES OF THE DEPARTMENT OF DEFENSE DRAWING APPROVAL DATE 93-03-31 AMSC N/A REVISION LEVEL C SIZE A CAGE CODE 67268 5962-92186 SHEET 1 OF 18 DSCC FORM 2233
5、 APR 97 5962- E261-13 Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 2 DSCC FORM 2234 APR 97 1. SCOPE 1.1 Scope. This drawing docu
6、ments two product assurance class levels consisting of high reliability (device classes Q and M) and space application (device class V). A choice of case outlines and lead finishes are available and are reflected in the Part or Identifying Number (PIN). When available, a choice of Radiation Hardness
7、 Assurance (RHA) levels is reflected in the PIN. 1.2 PIN. The PIN is as shown in the following example: 5962 R 92186 01 V R A Federal stock class designator RHA designator (see 1.2.1) Device type (see 1.2.2) Device class designator Case outline (see 1.2.4) Lead finish (see 1.2.5) / (see 1.2.3) / Dra
8、wing number 1.2.1 RHA designator. Device classes Q and V RHA marked devices meet the MIL-PRF-38535 specified RHA levels and are marked with the appropriate RHA designator. Device class M RHA marked devices meet the MIL-PRF-38535, appendix A specified RHA levels and are marked with the appropriate RH
9、A designator. A dash (-) indicates a non-RHA device. 1.2.2 Device type(s). The device type(s) identify the circuit function as follows: Device type Generic number Circuit function 01 54ACTQ244 Octal buffer/line driver with noninverting three-state outputs, TTL compatible inputs 1.2.3 Device class de
10、signator. The device class designator is a single letter identifying the product assurance level as follows: Device class Device requirements documentation M Vendor self-certification to the requirements for MIL-STD-883 compliant, non-JAN class level B microcircuits in accordance with MIL-PRF-38535,
11、 appendix A Q or V Certification and qualification to MIL-PRF-38535 1.2.4 Case outline(s). The case outline(s) are as designated in MIL-STD-1835 and as follows: Outline letter Descriptive designator Terminals Package style R GDIP1-T20 or CDIP2-T20 20 Dual-in-line S GDFP2-F20 or CDFP3-F20 20 Flat pac
12、k 2 CQCC1-N20 20 Square leadless chip carrier 1.2.5 Lead finish. The lead finish is as specified in MIL-PRF-38535 for device classes Q and V or MIL-PRF-38535, appendix A for device class M. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MIC
13、ROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 3 DSCC FORM 2234 APR 97 1.3 Absolute maximum ratings. 1/ 2/ 3/ Supply voltage range (VCC) . -0.5 V dc to +7.0 V dc DC input voltage range (VIN) . -0.5 V dc to VCC + 0.5 V dc DC output voltage r
14、ange (VOUT) -0.5 V dc to VCC+ 0.5 V dc DC input clamp current (IIK) (VIN= -0.5 V and VCC+ 0.5 V) . 20 mA DC output clamp current (IOK) (VOUT= -0.5 V and VCC+ 0.5 V) . 20 mA DC output current (IOUT) (per output pin) . 50 mA DC VCCor GND current (ICC, IGND) (per pin) 50 mA Maximum power dissipation (P
15、D) 500 mW Storage temperature range (TSTG) -65C to +150C Lead temperature (soldering, 10 seconds) . +300C Thermal resistance, junction-to-case (JC) . See MIL-STD-1835 Junction temperature (TJ) . +175C 4/ 1.4 Recommended operating conditions. 2/ 3/ Supply voltage range (VCC) . +4.5 V dc to +5.5 V dc
16、Input voltage range (VIN) . 0.0 V to VCC Output voltage range (VOUT) 0.0 V to VCCMaximum low level input voltage (VIL). 0.8 V Minimum high level input voltage (VIH) 2.0 V dc Case operating temperature range (TC) -55C to +125C Input rise and fall times (tr, tf) . 0 to 8 ns/V Maximum high level output
17、 current (IOH) . -24 mA Maximum low level output current (IOL) . +24 mA 1.5 Radiation features. Maximum total dose available (dose rate = 50 300 rads (Si)/s) . 1 x 105Rads(Si) 1/ Stresses above the absolute maximum rating may cause permanent damage to the device, Extended operation at the maximum le
18、vels may degrade performance and affect reliability. 2/ Unless otherwise noted, all voltages are referenced to GND. 3/ The limits for the parameters specified herein shall apply over the full specified VCCrange and case temperature range of -55C to +125C. 4/ Maximum junction temperature shall not be
19、 exceeded except for allowable short duration burn-in screening conditions in accordance with method 5004 of MIL-STD-883. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITIME COLUMBUS,
20、OHIO 43218-3990 REVISION LEVEL C SHEET 4 DSCC FORM 2234 APR 97 2. APPLICABLE DOCUMENTS 2.1 Government specification, standards, and handbooks. The following specification, standards, and handbooks form a part of this drawing to the extent specified herein. Unless otherwise specified, the issues of t
21、hese documents are those cited in the solicitation or contract. DEPARTMENT OF DEFENSE SPECIFICATION MIL-PRF-38535 - Integrated Circuits, Manufacturing, General Specification for. DEPARTMENT OF DEFENSE STANDARDS MIL-STD-883 - Test Method Standard Microcircuits. MIL-STD-1835 - Interface Standard Elect
22、ronic Component Case Outlines. DEPARTMENT OF DEFENSE HANDBOOKS MIL-HDBK-103 - List of Standard Microcircuit Drawings. MIL-HDBK-780 - Standard Microcircuit Drawings. (Copies of these documents are available online at https:/assist.dla.mil/quicksearch/ or from the Standardization Document Order Desk,
23、700 Robbins Avenue, Building 4D, Philadelphia, PA 19111-5094.) 2.2 Non-Government publications. The following document(s) form a part of this document to the extent specified herein. Unless otherwise specified, the issues of these documents are those cited in the solicitation or contract. JEDEC SOLI
24、D STATE TECHNOLOGY ASSOCIATION (JEDEC) JESD78 - IC Latch-Up Test. JESD20 - Standard for Description of 54/74ACXXXX and 54/74ACTXXXX Advanced High-Speed CMOS Devices. (Copies of these documents are available online at http:/www.jedec.org or from JEDEC Solid State Technology Association, 3103 North 10
25、th Street, Suite 240S, Arlington, VA 22201-2701.) 2.3 Order of precedence. In the event of a conflict between the text of this drawing and the references cited herein, the text of this drawing takes precedence. Nothing in this document, however, supersedes applicable laws and regulations unless a sp
26、ecific exemption has been obtained. 3. REQUIREMENTS 3.1 Item requirements. The individual item requirements for device classes Q and V shall be in accordance with MIL-PRF-38535 and as specified herein or as modified in the device manufacturers Quality Management (QM) plan. The modification in the QM
27、 plan shall not affect the form, fit, or function as described herein. The individual item requirements for device class M shall be in accordance with MIL-PRF-38535, appendix A for non-JAN class level B devices and as specified herein. 3.2 Design, construction, and physical dimensions. The design, c
28、onstruction, and physical dimensions shall be as specified in MIL-PRF-38535 and herein for device classes Q and V or MIL-PRF-38535, appendix A and herein for device class M. 3.2.1 Case outlines. The case outlines shall be in accordance with 1.2.4 herein. 3.2.2 Terminal connections. The terminal conn
29、ections shall be as specified on figure 1. 3.2.3 Truth table. The truth table shall be as specified on figure 2. 3.2.4 Logic diagram. The logic diagram shall be as specified on figure 3. 3.2.5 Ground bounce waveforms and test circuit. The ground bounce waveforms and test circuit shall be as specifie
30、d on figure 4. 3.2.6 Switching waveforms and test circuit. The switching waveforms and test circuit shall be as specified on figure 5. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITI
31、ME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 5 DSCC FORM 2234 APR 97 3.2.7 Radiation exposure circuit. The radiation exposure circuit shall be maintained by the manufacturer under document revision level control and shall be made available to the preparing and acquiring activity upon request.
32、 3.3 Electrical performance characteristics and postirradiation parameter limits. Unless otherwise specified herein, the electrical performance characteristics and postirradiation parameter limits are as specified in table I and shall apply over the full case operating temperature range. 3.4 Electri
33、cal test requirements. The electrical test requirements shall be the subgroups specified in table II. The electrical tests for each subgroup are defined in table I. 3.5 Marking. The part shall be marked with the PIN listed in 1.2 herein. In addition, the manufacturers PIN may also be marked. For pac
34、kages where marking of the entire SMD PIN number is not feasible due to space limitations, the manufacturer has the option of not marking the “5962-“ on the device. For RHA product using this option, the RHA designator shall still be marked. Marking for device classes Q and V shall be in accordance
35、with MIL-PRF-38535. Marking for device class M shall be in accordance with MIL-PRF-38535, appendix A. 3.5.1 Certification/compliance mark. The certification mark for device classes Q and V shall be a “QML“ or “Q“ as required in MIL-PRF-38535. The compliance mark for device class M shall be a “C“ as
36、required in MIL-PRF-38535, appendix A. 3.6 Certificate of compliance. For device classes Q and V, a certificate of compliance shall be required from a QML-38535 listed manufacturer in order to supply to the requirements of this drawing (see 6.6.1 herein). For device class M, a certificate of complia
37、nce shall be required from a manufacturer in order to be listed as an approved source of supply in MIL-HDBK-103 (see 6.6.2 herein). The certificate of compliance submitted to DLA Land and Maritime-VA prior to listing as an approved source of supply for this drawing shall affirm that the manufacturer
38、s product meets, for device classes Q and V, the requirements of MIL-PRF-38535 and herein or for device class M, the requirements of MIL-PRF-38535, appendix A and herein. 3.7 Certificate of conformance. A certificate of conformance as required for device classes Q and V in MIL-PRF-38535 or for devic
39、e class M in MIL-PRF-38535, appendix A shall be provided with each lot of microcircuits delivered to this drawing. 3.8 Notification of change for device class M. For device class M, notification to DLA Land and Maritime-VA of change of product (see 6.2 herein) involving devices acquired to this draw
40、ing is required for any change that affects this drawing. 3.9 Verification and review for device class M. For device class M, DLA Land and Maritime, DLA Land and Maritimes agent, and the acquiring activity retain the option to review the manufacturers facility and applicable required documentation.
41、Offshore documentation shall be made available onshore at the option of the reviewer. 3.10 Microcircuit group assignment for device class M. Device class M devices covered by this drawing shall be in microcircuit group number 37 (see MIL-PRF-38535, appendix A). Provided by IHSNot for ResaleNo reprod
42、uction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 6 DSCC FORM 2234 APR 97 TABLE I. Electrical performance characteristics. Test and MIL-STD-883 test method 1/ Symbol Test
43、conditions 2/ 3/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type and device class VCCGroup A subgroups Limits 4/ Unit Min Max High level output voltage 3006 VOHFor all inputs affecting outputs under test, VIN=VIH=2.0V or VIL= 0.8V For all other inputs, VIN= VCCor GND IOH= -50
44、A All All 4.5 V 1, 2, 3 4.40 V 5.5 V 1, 2, 3 5.40 For all inputs affecting outputs under test, VIN=VIH=2.0V or VIL= 0.8V For all other inputs, VIN= VCCor GND IOH= -24 mA All All 4.5 V 1 3.86 2, 3 3.70 5.5 V 1 4.86 2, 3 4.70 For all inputs affecting outputs under test, VIN=VIH=2.0V or VIL= 0.8V For a
45、ll other inputs, VIN= VCCor GND IOH= -50 mA 5/ All All 5.5 V 1, 2, 3 3.85 Low level output voltage 3007 VOLFor all inputs affecting outputs under test, VIN=VIH=2.0V or VIL= 0.8V For all other inputs, VIN= VCCor GND IOL= 50 A All All 4.5 V 1, 2, 3 0.10 V 5.5 V 1, 2, 3 0.10 For all inputs affecting ou
46、tputs under test, VIN=VIH=2.0V or VIL= 0.8V For all other inputs, VIN= VCCor GND IOL= 24 mA All All 4.5 V 1 0.36 2, 3 0.50 5.5 V 1 0.36 2, 3 0.50 For all inputs affecting outputs under test, VIN=VIH=2.0V or VIL= 0.8V For all other inputs, VIN= VCCor GND IOL= 50 mA 5/ All All 5.5 V 1, 2, 3 1.65 See f
47、ootnotes at end of table. Provided by IHSNot for ResaleNo reproduction or networking permitted without license from IHS-,-,-STANDARD MICROCIRCUIT DRAWING SIZE A 5962-92186 DLA LAND AND MARITIME COLUMBUS, OHIO 43218-3990 REVISION LEVEL C SHEET 7 DSCC FORM 2234 APR 97 TABLE I. Electrical performance c
48、haracteristics Continued. Test and MIL-STD-883 test method 1/ Symbol Test conditions 2/ 3/ -55C TC +125C +4.5 V VCC +5.5 V unless otherwise specified Device type and device class VCCGroup A subgroups Limits 4/ Unit Min Max Positive input clamp voltage 3022 VIC+For input under test, IIN= 1 mA All Q, V GND 1, 2, 3 0.4 1.5 V Negative input clamp voltage 3022 VIC-For input under test, IIN= -1 mA All Q, V Open 1, 2, 3 -0.4 -1.5 Input leakage current high 3010 IIHFor input under test, VIN= 5.5 V For all other inputs, VIN= VCCor GND All All 5.5 V 1 0.1 A A
